Oversize and Overweight Vehicles and Loads
Not legal advice. Always verify with the issuing authority and the permit text before moving. Editorial copy for reference — not a substitute for the official publication.
Partial copy. Some sections are present. Gaps are marked and are not law. Never invent missing text. Rule text from the Texas Department of Motor Vehicles June 27, 2024 adoption exhibit. Running headers, exhibit line numbers, and the adoption preamble are omitted. The exhibit marks §§219.84, 219.86, and 219.123 as repealed; those bracketed repeal texts are omitted. The struck words [Single Trip] in §219.62 are omitted; the catchline in the exhibit is Single-Trip Mileage Permits. Figures 1 and 2 of §219.42(f) and §219.62(f) are copied from the Texas Secretary of State attached graphics 201502155-1, 201502155-2, 201502158-1, and 201502158-2, dated June 8, 2015. Section 219.3 is named once in the adoption preamble and is not reprinted as rule text in the exhibit.
Official publication · Texas Department of Motor Vehicles
Chapter 219 — Oversize and Overweight Vehicles and Loads
Title 43, Part 10, Texas Department of Motor Vehicles. The text below is the rule text in the department’s June 27, 2024 adoption exhibit.
Subchapter A. General Provisions
§219.1. Purpose and Scope.
The department is responsible for regulating the movement of oversize and overweight vehicles and loads on certain public roadways in this state, in order to ensure the safety of the traveling public, and to protect the integrity of the public roadways and the bridges. This responsibility is accomplished through the issuance of permits for the movement of oversize and overweight vehicles and loads. The sections under this chapter prescribe the policies and procedures for the issuance of permits and the filing of surety bonds. All applications for permits and all questions regarding the permits should be directed to the department, even though TxDOT is responsible for certain issues regarding permits.
§219.2. Definitions.
(a) The definitions contained in Transportation Code, Chapters 621, 622, and 623 apply to this chapter. In the event of a conflict with this chapter, the definitions contained in Transportation Code, Chapters 621, 622, and 623 control.
(b) The following words and terms, when used in this chapter, will have the following meanings, unless the context clearly indicates otherwise.
(1) Annual permit--A permit that authorizes movement of an oversize and/or overweight load for one year commencing with the effective date.
(2) Applicant--Any person, firm, or corporation requesting a permit.
(3) Axle--The common axis of rotation of one or more wheels whether power-driven or freely rotating, and whether in one or more segments.
(4) Axle group--An assemblage of two or more consecutive axles, with two or more wheels per axle, spaced at least 40 inches from center of axle to center of axle, equipped with a weight-equalizing suspension system that will not allow more than a 10% weight difference between any two axles in the group.
(5) Closeout--The procedure used by the department to terminate a permit, issued under Transportation Code, §623.142 or §623.192 that will not be renewed by the applicant.
(6) Complete identification number--A unique and distinguishing number assigned to equipment or a commodity for purposes of identification.
(7) Concrete pump truck--A self-propelled vehicle designed to pump the concrete product from a ready mix truck to the point of construction.
(8) Crane--Any unladen lift equipment motor vehicle designed for the sole purpose of raising, shifting, or lowering heavy weights by means of a projecting, swinging mast with an engine for power on a chassis permanently constructed or assembled for such purpose.
(9) Day—A calendar day.
(10) Daytime--As defined in Transportation Code, §541.401.
(11) Digital signature--An electronic identifier intended by the person using it to have the same force and effect as a manual signature. The digital signature shall be unique to the person using it.
(12) Electronic identifier--A unique identifier which is distinctive to the person using it, is independently verifiable, is under the sole control of the person using it, and is transmitted in a manner that makes it infeasible to change the data in the communication or digital signature without invalidating the digital signature.
(13) Escort flag vehicle--A vehicle that precedes or follows an oversize or overweight vehicle to facilitate the safe movement of the oversize or overweight vehicle over roads.
(14) Four-axle group--Any four consecutive axles, having at least 40 inches from center of axle to center of axle, whose extreme centers are not more than 192 inches apart and are individually attached to or articulated from, or both, to the vehicle by a weight equalizing suspension system.
(15) Gauge--The transverse spacing distance between tires on an axle, expressed in feet and measured to the nearest inch, from center-of-tire to center-of-tire on an axle equipped with only two tires, or measured to the nearest inch from the center of the dual wheels on one side of the axle to the center of the dual wheels on the opposite side of the axle.
(16) Gross weight--The unladen weight of a vehicle or combination of vehicles plus the weight of the load being transported.
(17) Height pole--A device made of a non-conductive material, used to measure the height of overhead obstructions.
(18) Highway maintenance fee--A fee established by Transportation Code, §623.077, based on gross weight, and paid by the permittee when the permit is issued.
(19) Highway use factor--A mileage reduction figure used in the calculation of a permit fee for a permit issued under Transportation Code, §623.142 and §623.192.
(20) Hubometer--A mechanical device attached to an axle on a unit or an unladen lift equipment motor vehicle for recording mileage traveled.
(21) HUD label number--A unique number assigned to a manufactured home by the U.S. Department of Housing and Urban Development.
(22) Indirect cost share--A prorated share of administering department activities, other than the direct cost of the activities, including the cost of providing statewide support services.
(23) Load-restricted bridge--A bridge that is restricted by the Texas Department of Transportation, under the provisions of Transportation Code, §621.102, to a weight limit less than the maximum amount allowed by Transportation Code, §621.101.
(24) Load-restricted road--A road that is restricted by the Texas Department of Transportation, under the provisions of Transportation Code, §621.102, to a weight limit less than the maximum amount allowed by Transportation Code, §621.101.
(25) Manufactured home--Manufactured housing, as defined in Occupations Code, Chapter 1201, and industrialized housing and buildings, as defined in Occupations Code, §1202.002, and temporary chassis systems, and returnable undercarriages used for the transportation of manufactured housing and industrialized housing and buildings, and a transportable section which is transported on a chassis system or returnable undercarriage that is constructed so that it cannot, without dismantling or destruction, be transported within legal size limits for motor vehicles.
(26) Motor carrier--A person that controls, operates, or directs the operation of one or more vehicles that transport persons or cargo over a public highway in this state, as defined by Transportation Code, §643.001.
(27) Nighttime—As defined in Transportation Code, §541.401.
(28) Nondivisible load or vehicle--
(A) A nondivisible load or vehicle is defined as follows:
(i) Any load or vehicle exceeding applicable length or weight limits which, if separated into smaller loads or vehicles, would:
(I) compromise the intended use of the vehicle, i.e., make it unable to perform the function for which it was intended;
(II) destroy the value of the load or vehicle, i.e., make it unusable for its intended purpose; or
(III) require more than eight workhours to dismantle using appropriate equipment. The applicant for a nondivisible load permit has the burden of proof as to the number of workhours required to dismantle the load.
(ii) Emergency response vehicles, including those loaded with salt, sand, chemicals or a combination thereof, with or without a plow or blade attached in front, and being used for the purpose of spreading the material on highways that are or may become slick or icy.
(iii) Casks designed for the transport of spent nuclear materials.
(iv) Military vehicles transporting marked military equipment or materiel.
(B) A vehicle or load that exceeds legal weight (without the properly secured components) and for which an appropriate permit is obtained from the department under this chapter may travel as a mobile vehicle or as a load, as applicable, with properly secured components in accordance with the manufacturer's specifications to the extent the components are necessary for the vehicle or load to perform its intended function or purpose, provided the axle weights, axle group weights, and gross weight do not exceed the maximum applicable permit weights listed in this chapter. For example, a crane permitted under Subchapter E of this chapter that exceeds legal weight without the properly secured components may travel with properly secured components, such as outriggers, booms, counterweights, jibs, blocks, balls, cribbing, outrigger pads, and outrigger mats, in accordance with the manufacturer's specifications to the extent the components are necessary for the crane to perform its intended function, provided the axle weights, axle group weights, and gross weight do not exceed the maximum permit weights listed in Subchapter E of this chapter. An example of a load being transported is a dozer with the blade detached that is permitted under §219.12 of this title (relating to Single-Trip Permits Issued under Transportation Code, Chapter 623, Subchapter D) when both are being transported on a trailer or semitrailer if the dozer without the blade is overweight, provided the axle weights, axle group weights, and gross weight do not exceed the maximum permit weights listed in §219.12.
(29) Oil field rig-up truck--An unladen vehicle with an overweight single steering axle, equipped with a winch and set of gin poles used for lifting, erecting, and moving oil well equipment and machinery.
(30) Oil well servicing unit--An oil well clean-out unit, oil well drilling unit, or oil well swabbing unit, which is mobile equipment, either self-propelled or trailer-mounted, constructed as a machine used solely for cleaning-out, drilling, servicing, or swabbing oil wells, and consisting in general of, but not limited to, a mast, an engine for power, a draw works, and a chassis permanently constructed or assembled for this purpose.
(31) Overdimension load--A vehicle, combination of vehicles, or vehicle and its load that exceeds maximum legal width, height, length, overhang, or weight as set forth by Transportation Code, Chapter 621, Subchapters B and C.
(32) Overhang--The portion of a load extending beyond the front or rear of a vehicle or combination of vehicles.
(33) Overheight--A vehicle or load that exceeds the maximum height specified in Transportation Code, §621.207.
(34) Overlength--A vehicle, combination of vehicles, or a vehicle or vehicle combination and its load that exceed(s) the maximum length specified in Transportation Code, §§621.203, 621.204, 621.205, and 621.206.
(35) Oversize load--A vehicle, combination of vehicles, or a vehicle or vehicle combination and its load that exceed(s) maximum legal width, height, length, or overhang, as set forth by Transportation Code, Chapter 621, Subchapter C.
(36) Overweight--A vehicle, combination of vehicles, or a vehicle or vehicle combination and its load that exceed(s) the maximum weight specified in Transportation Code, §621.101.
(37) Overwidth--A vehicle or load that exceeds the maximum width specified in Transportation Code, §621.201.
(38) Permit--Authority for the movement of an oversize and/or overweight vehicle, combination of vehicles, or a vehicle or vehicle combination and its load, issued by the department under Transportation Code, Chapter 623.
(39) Permit officer--An employee of the department who is authorized to issue an oversize/overweight permit.
(40) Permit plate--A license plate issued under Transportation Code, §502.146, to oil well servicing, cleanout, or drilling machinery as defined in Transportation Code, §502.001(29).
(41) Permitted vehicle--A vehicle, combination of vehicles, or vehicle and its load operating under the provisions of a permit.
(42) Permittee--Any person, firm, or corporation that is issued an oversize/overweight permit by the department.
(43) Pipe box--A container specifically constructed to safely transport and handle oil field drill pipe and drill collars.
(44) Portable building compatible cargo--Cargo, other than a portable building unit, that is manufactured, assembled, or distributed by a portable building unit manufacturer and is transported in combination with a portable building unit.
(45) Portable building unit--The pre-fabricated structural and other components incorporated and delivered by the manufacturer as a complete inspected unit with a distinct serial number whether in fully assembled, partially assembled, or kit (unassembled) configuration when loaded for transport.
(46) Principal--The person, firm, or corporation that is insured by a surety bond company.
(47) Roll stability support safety system--An electronic system that monitors vehicle dynamics and estimates the stability of a vehicle based on its mass and velocity, and actively adjusts vehicle systems including the throttle and/or brake(s) to maintain stability when a rollover risk is detected.
(48) Shipper's certificate of weight--A form approved by the department in which the shipper certifies to the maximum weight of the shipment being transported.
(49) Single axle--An assembly of two or more wheels whose centers are in one transverse vertical plane or may be included between two parallel transverse planes 40 inches apart extending across the full width of the vehicle.
(50) Single-trip permit--A permit issued for an overdimension load for a single continuous movement over a specific route for an amount of time necessary to make the movement.
(51) State highway--A highway or road under the jurisdiction of the Texas Department of Transportation.
(52) State highway system--A network of roads and highways as defined by Transportation Code, §221.001.
(53) Surety bond--An agreement issued by a surety bond company to a principal that pledges to compensate the obligee as required under Transportation Code, Chapters 622 and 623.
(54) Tare weight--The empty weight of any vehicle transporting an overdimension load.
(55) Three-axle group--Any three consecutive axles, having at least 40 inches from
center of axle to center of axle, whose extreme centers are not more than 144 inches apart, and
are individually attached to or articulated from, or both, to the vehicle by a weight equalizing
suspension system.
(56) Time permit--A permit issued for a specified period of time under §219.13 of this title (relating to Time Permits).
(57) Tire size--The inches of lateral tread width.
(58) Trailer-mounted unit--An oil well clean-out, drilling, servicing, or swabbing unit mounted on a trailer, constructed as a machine used for cleaning out, drilling, servicing, or swabbing oil wells, and consisting in general of, but not limited to, a mast, an engine for power, a draw works, and a chassis permanently constructed or assembled for this purpose.
(59) Truck--A motor vehicle designed, used, or maintained primarily for the transportation of property.
(60) Truck blind spot systems--Vehicle-based sensor devices that detect other vehicles or objects located in the vehicle's adjacent lanes. Warnings can be visual, audible, vibrating, or tactile.
(61) Trunnion axle--Two individual axles mounted in the same transverse plane, with four tires on each axle, that are connected to a pivoting wrist pin that allows each individual axle to oscillate in a vertical plane to provide for constant and equal weight distribution on each individual axle at all times during movement.
(62) Two-axle group--Any two consecutive axles whose centers are at least 40 inches but not more than 96 inches apart and are individually attached to or articulated from, or both, to the vehicle by a weight equalizing suspension system.
(63) TxDOT--Texas Department of Transportation.
(64) Unit--Oil well clean-out unit, oil well drilling unit, oil well servicing unit, and/or oil well swabbing unit.
(65) Unladen lift equipment motor vehicle--A motor vehicle, such as a crane or a concrete pump truck, designed for use as lift equipment used solely to raise, shift, or lower heavy weights by means of a projecting, swinging mast with an engine for power on a chassis permanently constructed or assembled for such purpose.
(66) USDOT Number--The United States Department of Transportation number.
(67) Vehicle identification number--A unique and distinguishing number assigned to a vehicle by the manufacturer or by the department in accordance with Transportation Code, §501.032 and §501.033.
(68) Water Well Drilling Machinery--Machinery used exclusively for the purpose of drilling water wells, including machinery that is a unit or a unit mounted on a conventional vehicle or chassis.
(69) Weight-equalizing suspension system--An arrangement of parts designed to attach two or more consecutive axles to the frame of a vehicle in a manner that will equalize the load between the axles.
(70) Windshield sticker--Identifying insignia indicating that a permit has been issued in accordance with Subchapter C of this chapter.
(71) Year--A time period consisting of 12 consecutive months that commences with the effective date stated in the permit.
§219.5. Application Requirements.
(a) An application for a permit under this chapter must be filed with the department and must be:
(1) made in a form and filed by the method prescribed by the department on its website;
(2) completed by the applicant or an authorized representative of the applicant; and
(3) accompanied by the required fee, which shall be payable as provided by §209.23 of this title (relating to Methods of Payment).
(b) An authorized representative of the applicant who files an application with the department on behalf of the applicant may be required to provide written proof of authority to act on behalf of the applicant.
(c) The department will not approve an application for a permit unless the applicant:
(1) provides all information and documents required by the department; and
(2) complies with all application requirements under this chapter; Transportation Code, Chapters 621, 622, and 623; and other applicable law.
(d) An applicant must register for an account in the department’s designated permitting system prior to using the system to apply for or amend a permit. Once the applicant registers for an account in the department’s designated permitting system, the system will generate a customer identification number for the applicant to use when applying for a permit. To register for an account, the applicant must provide the following information via the department’s designated permitting system, which is accessible on the department’s website:
(1) the applicant’s company name, phone number, email address, permit delivery method, physical address, and mailing address;
(2) first name, last name, and phone number for an emergency contact for the applicant; and
(3) the requested login information, including a unique username and password.
(e) If the department authorizes an application for a permit to be submitted by mail and the applicant does not have a customer identification number, the applicant must authorize the department to set up an account for the applicant in the department’s designated permitting system for the purposes of obtaining a customer identification number for the applicant based on information the department obtains from the applicant’s permit application and information the department obtains from the Federal Motor Carrier Safety Administration’s system.
§219.7. Amendments to Permits.
(a) General amendment guidelines. Except as provided by subsection (b) of this section, any part of a permit may be amended under the guidelines in this subsection, notwithstanding any other sections in this chapter regarding limitations on amending a permit.
(1) Any amendment that is necessary to correct an error made by department staff or the department’s designated permitting system may be made provided the price of the permit or the permit type does not change.
(2) An expired permit may only be amended if it expired on a day on which the department was closed or the department’s designated permitting system was not operational.
(b) Specific amendment authority and restrictions. Notwithstanding any other section in this chapter regarding limitations on amending a permit, a permit issued under this chapter may be amended as authorized by this subsection.
(1) The permittee’s name can be amended on any permit type to correct a spelling error.
(2) The permittee’s contact information may be amended on any permit type.
§219.9. Federal Highway Administration Interpretation of Federal Law.
Notwithstanding any provisions in this chapter, this chapter does not authorize the operation of a vehicle or vehicle combination on the following roadways in this state to the extent the Federal Highway Administration determines the vehicle or vehicle combination exceeds the applicable weight or size for such roadway under 23 U.S.C. §127, 49 U.S.C. §§31111 through 31114, or federal regulations prescribed under 23 U.S.C. §127 or 49 U.S.C. §§31111 through 31114: the federal-aid primary system, the federal-aid urban system, and the federal-aid secondary system, including the national system of interstate and defense highways. To the extent the department learns that the Federal Highway Administration generally determines a vehicle or vehicle combination exceeds the applicable weight or size for such roadway under 23 U.S.C. §127, 49 U.S.C. §§31111 through 31114, or federal regulations prescribed under 23 U.S.C. §127 or 49 U.S.C. §§31111 through 31114 in a way that may conflict with a provision in this chapter, the department will post a notice on its website and may provide notice to permittees through the applicable email addresses on file with the department.
Subchapter B. General Permits
§219.11. General Oversize/Overweight Permit Requirements and Procedures.
(a) Purpose and scope. This section contains general requirements relating to oversize/overweight permits, including single-trip permits. Specific requirements for each type of specialty permit are provided for in this chapter.
(b) Motor carrier registration or surety bond. Unless exempted by law, prior to obtaining an oversize/overweight permit, an applicant permitted under the provisions of Transportation Code, Chapter 623, Subchapter D, must be registered as a motor carrier under Chapter 218 of this title (relating to Motor Carriers) or, if not required to obtain a motor carrier registration, file a surety bond with the department as described in subsection (n) of this section.
(c) Permit application.
(1) An application for a permit shall be made in a form and by the method prescribed by the department, and at a minimum shall include the following, unless stated otherwise in this subchapter:
(A) name, customer identification number, and address of the applicant;
(B) name, telephone number, and email address of contact person;
(C) applicant's USDOT Number if applicant is required by law to have a USDOT Number;
(D) complete load description, including maximum width, height, length, overhang, and gross weight;
(E) complete description of vehicle, including truck year, make, license plate number and state of issuance, and vehicle identification number, if required;
(F) vehicle axle and tire information including number of axles, distance between axles, axle weights, number of tires, and tire size for overweight permit applications; and
(G) any other information required by law.
(2) Applications transmitted electronically are considered signed if a digital signature is transmitted with the application and intended by the applicant to authenticate the application.
(A) The department may only accept a digital signature used to authenticate an application under procedures that comply with any applicable rules adopted by the Department of Information Resources regarding department use or acceptance of a digital signature.
(B) The department may only accept a digital signature to authenticate an application if the digital signature is:
(i) unique to the person using it;
(ii) capable of independent verification;
(iii) under the sole control of the person using it; and
(iv) transmitted in a manner that will make it infeasible to change the data in the communication or digital signature without invalidating the digital signature.
(d) Maximum permit weight limits.
(1) General. An overweight permitted vehicle will not be routed over a load-restricted bridge when exceeding the posted capacity of the bridge, unless a special exception is granted by TxDOT, based on an analysis of the bridge performed by a TxDOT approved licensed professional engineer or by TxDOT. Any analysis by a non-TxDOT licensed professional engineer must have final approval from TxDOT.
(A) An axle group must have a minimum spacing of four feet, measured from center of axle to center of axle, between each axle in the group to achieve the maximum permit weight for the group.
(B) The maximum permit weight for an axle group with spacing of five or more feet between each axle will be based on an engineering study of the equipment conducted by TxDOT.
(C) A permitted vehicle will be allowed to have air suspension, hydraulic suspension, and mechanical suspension axles in a common weight equalizing suspension system for any axle group.
(D) The department may permit axle weights greater than those specified in this section, for a specific individual permit request, based on an engineering study of the route and hauling equipment performed by a TxDOT approved licensed professional engineer or by TxDOT. Any analysis by a non-TxDOT licensed professional engineer must have final approval from TxDOT.
(E) A permitted vehicle or combination of vehicles may not exceed the manufacturer's rated tire carrying capacity, unless expressly authorized in the language on the permit based on an analysis performed by a TxDOT approved licensed professional engineer or by TxDOT. Any analysis by a non-TxDOT licensed professional engineer must have final approval from TxDOT.
(F) If two or more consecutive axle groups have an axle spacing of less than 12 feet, measured from the center of the last axle of the preceding group to the center of the first axle of the following group, the maximum permit weight on the axle groups will be reduced by 2.5% for each foot less than 12 feet.
(2) Maximum axle weight limits. Maximum permit weight for an axle or axle group is based on 650 pounds per inch of tire width or the following axle or axle group weights, whichever is the lesser amount:
(A) single axle--25,000 pounds;
(B) two-axle group--46,000 pounds;
(C) three-axle group--60,000 pounds;
(D) four-axle group--70,000 pounds;
(E) five-axle group--81,400 pounds;
(F) axle group with six or more axles--determined by TxDOT based on an engineering study of the equipment, which will include the type of steering system used, the type of axle suspension, the spacing distance between each axle, the number of tires per axle, and the tire size on each axle; or
(G) trunnion axles--30,000 pounds per axle if the trunnion configuration has:
(i) two axles;
(ii) eight tires per axle;
(iii) axles a minimum of 10 feet in width; and
(iv) at least five feet of spacing between the axles, not to exceed six feet.
(3) Weight limits for load restricted roads. Maximum permit weight for an axle or axle group, when traveling on a load restricted road, will be based on 650 pounds per inch of tire width or the following axle or axle group weights, whichever is the lesser amount:
(A) single axle--22,500 pounds;
(B) two-axle group--41,400 pounds;
(C) three-axle group--54,000 pounds;
(D) four-axle group--63,000 pounds;
(E) five-axle group--73,260 pounds;
(F) axle group with six or more axles--determined by TxDOT based on an engineering study of the equipment, which will include the type of steering system used, the type of axle suspension, the spacing distance between each axle, the number of tires per axle, and the tire size on each axle;
(G) trunnion axles--54,000 pounds; and
(H) if two or more consecutive axle groups have an axle spacing of less than 12 feet, measured from the center of the last axle of the preceding group to the center of the first axle of the following group, the maximum permit weight on the axle groups will be reduced by 2.5% for each foot less than 12 feet.
(e) Permit issuance.
(1) General. Upon receiving an application in the form prescribed by the department, the department will review the permit application for the appropriate information and will then determine the most practical route based on information provided by TxDOT.
(2) Routing.
(A) A permitted vehicle will be routed over the most practical route available taking into consideration:
(i) the size and weight of the overdimension load in relation to vertical clearances, width restrictions, steep grades, and reduced capacity or load restricted bridges;
(ii) the geometrics of the roadway in comparison to the overdimension load;
(iii) sections of highways restricted to specific load sizes and weights due to construction, maintenance, and hazardous conditions;
(iv) traffic conditions, including traffic volume;
(v) route designations by municipalities in accordance with Transportation Code, §623.072;
(vi) load restricted roads; and
(vii) other considerations for the safe transportation of the load.
(B) When a permit applicant desires a route other than the most practical, more than one permit will be required for the trip unless an exception is granted by the department.
(3) Movement to and from point of origin or place of business. A permitted vehicle will be allowed to:
(A) move empty oversize and overweight hauling equipment to and from the job site; and
(B) move oversize and overweight hauling equipment with a load from the permitted vehicle's point of origin to pick up a permitted load, and to the permitted vehicle's point of origin or the permittee's place of business after dropping off a permitted load, as long as:
(i) the load does not exceed legal size and weight limits under Transportation Code, Chapters 621 and 622; and
(ii) the transport complies with the permit, including the time period stated on the permit.
(f) Refund of permit fees. A permit fee will not be refunded after the permit number has been issued unless such refund is necessary to correct an error made by the permit officer.
(g) Amendments. A permit may be amended for the following reasons:
(1) vehicle breakdown;
(2) changing the intermediate points in an approved permit route;
(3) extending the expiration date due to conditions which would cause the move to be delayed;
(4) changing route origin or route destination prior to the start date as listed on the permit;
(5) changing vehicle size limits prior to the permit start date as listed on the permit, provided that changing the vehicle size limit does not necessitate a change in the approved route; and
(6) correcting any mistake that is made due to permit officer error.
(h) Requirements for overwidth loads.
(1) Unless stated otherwise on the permit, an overwidth load must travel in the outside traffic lane on multi-lane highways, when the width of the load exceeds 12 feet.
(2) Overwidth loads are subject to the escort requirements of subsection (k) of this section.
(3) A permitted vehicle exceeding 16 feet in width will not be routed on the main lanes of a controlled access highway, unless an exception is granted by TxDOT, based on a route and traffic study. The load may be permitted on the frontage roads when available, if the movement will not pose a safety hazard to other highway users.
(4) An applicant requesting a permit to move a load exceeding 20 feet wide will be furnished with a proposed route. The applicant must physically inspect the proposed route to determine if the vehicle and load can safely negotiate it, unless an exception is granted based on a route and traffic study conducted by TxDOT. A permit application and the appropriate fee are required for every route inspection.
(A) The applicant must notify the department in writing whether the vehicle and load can or cannot safely negotiate the proposed route.
(B) If any section of the proposed route is unacceptable, the applicant shall provide the department with an alternate route around the unacceptable section.
(C) Once a route is decided upon and a permit issued, the permit may not be amended unless an exception is granted by the department.
(i) Requirements for overlength loads.
(1) Overlength loads are subject to the escort requirements stated in subsection (k) of this section.
(2) A single vehicle, such as a motor crane, that has a permanently mounted boom is not considered as having either front or rear overhang as a result of the boom because the boom is an integral part of the vehicle.
(3) When a single vehicle with a permanently attached boom exceeds the maximum legal length of 45 feet, a permit will not be issued if the boom projects more than 25 feet beyond the front bumper of the vehicle, or when the boom projects more than 30 feet beyond the rear bumper of the vehicle, unless an exception is granted by TxDOT, based on a route and traffic study.
(4) Maximum permit length for a single vehicle is 75 feet.
(5) A load extending more than 20 feet beyond the front or rearmost portion of the load carrying surface of the permitted vehicle must have a rear escort flag vehicle, unless an exception is granted by TxDOT, based on a route and traffic study.
(6) A permit will not be issued for an oversize vehicle and load with:
(A) more than 25 feet front overhang; or
(B) more than 30 feet rear overhang, unless an exception is granted by TxDOT, based on a route and traffic study.
(7) An applicant requesting a permit to move an oversize vehicle and load exceeding 125 feet overall length will be furnished with a proposed route. The applicant must physically inspect the proposed route to determine if the oversize vehicle and load can safely negotiate it, unless an exception is granted based on a route and traffic study conducted by TxDOT. A permit application and the appropriate fee are required for every route inspection.
(A) The applicant must notify the department in writing whether the oversize vehicle and load can or cannot safely negotiate the proposed route.
(B) If any section of the proposed route is unacceptable, the applicant shall provide the department with an alternate route around the unacceptable section.
(C) Once a route is decided upon and a permit issued, the permit may not be amended unless an exception is granted by the department.
(8) A permitted vehicle that is not overwidth or overheight, and does not exceed 150 feet overall length, may be moved in a convoy consisting of not more than four overlength permitted vehicles. A permitted vehicle that is not overwidth or overheight that exceeds 150 feet, but does not exceed 180 feet overall length, may be moved in a convoy consisting of not more than two overlength permitted vehicles. Convoys are subject to the requirements of subsection (k) of this section. Each permitted vehicle in the convoy must:
(A) be spaced at least 1,000 feet, but not more than 2,000 feet, from any other permitted vehicle in the convoy; and
(B) have a rotating amber beacon or an amber pulsating light, not less than eight inches in diameter, mounted at the rear top of the load being transported.
(j) Requirements for overheight loads.
(1) Overheight loads are subject to the escort requirements stated in subsection (k) of this section.
(2) An applicant requesting a permit to move an oversize vehicle and load with an overall height of 19 feet or greater will be furnished with a proposed route. The applicant must physically inspect the proposed route to determine if the oversize vehicle and load can safely negotiate it, unless an exception is granted based on a route and traffic study conducted by TxDOT. A permit application and the appropriate fee are required for every route inspection.
(A) The applicant must notify the department in writing whether the oversize vehicle and load can or cannot safely negotiate the proposed route.
(B) If any section of the proposed route is unacceptable, the applicant shall provide the department with an alternate route around the unacceptable section.
(C) Once a route is decided upon and a permit issued, the permit may not be amended unless an exception is granted by the department.
(k) Escort flag vehicle requirements. Escort flag vehicle requirements are provided to facilitate the safe movement of permitted vehicles and to protect the traveling public during the movement of permitted vehicles. A permittee must provide for escort flag vehicles and law enforcement assistance when required by TxDOT. The requirements in this subsection do not apply to the movement of manufactured housing, portable building units, or portable building compatible cargo, unless stated otherwise in this chapter.
(1) General.
(A) Applicability. The operator of an escort flag vehicle shall, consistent with applicable law, warn the traveling public when:
(i) a permitted vehicle must travel over the center line of a narrow bridge or roadway;
(ii) a permitted vehicle makes any turning movement that will require the permitted vehicle to travel in the opposing traffic lanes;
(iii) a permitted vehicle reduces speed to cross under a low overhead obstruction or over a bridge;
(iv) a permitted vehicle creates an abnormal and unusual traffic flow pattern; or
(v) in the opinion of TxDOT, warning is required to ensure the safety of the traveling public or safe movement of the permitted vehicle.
(B) Law enforcement assistance. Law enforcement assistance may be required by TxDOT to control traffic when a permitted vehicle is being moved within the corporate limits of a city, or at such times when law enforcement assistance would provide for the safe movement of the permitted vehicle and the traveling public.
(C) Obstructions. It is the responsibility of the permittee to contact utility companies, telephone companies, television cable companies, or other entities as they may require, when it is necessary to raise or lower any overhead wire, traffic signal, street light, television cable, sign, or other overhead obstruction. The permittee is responsible for providing the appropriate advance notice as required by each entity.
(2) Escort requirements for overwidth loads. Unless an exception is granted based on a route and traffic study conducted by TxDOT, an overwidth load must:
(A) have a front escort flag vehicle if the width of the load exceeds 14 feet, but does not exceed 16 feet, when traveling on a two lane roadway;
(B) have a rear escort flag vehicle if the width of the load exceeds 14 feet, but does not exceed 16 feet, when traveling on a roadway of four or more lanes; and
(C) have a front and a rear escort flag vehicle for all roads, when the width of the load exceeds 16 feet.
(3) Escort requirements for overlength loads. Unless an exception is granted by TxDOT, based on a route and traffic study, overlength loads must have:
(A) a front escort flag vehicle when traveling on a two lane roadway if the vehicle exceeds 110 feet overall length, but does not exceed 125 feet overall length;
(B) a rear escort flag vehicle when traveling on a multi-lane highway if the vehicle exceeds 110 feet overall length, but does not exceed 125 feet overall length; and
(C) a front and rear escort flag vehicle at all times if the permitted vehicle exceeds 125 feet overall length.
(4) Escort requirements for overheight loads. Unless an exception is granted by TxDOT, based on a route and traffic study, overheight loads must have:
(A) a front escort flag vehicle equipped with a height pole to ensure the vehicle and load can clear all overhead obstructions for any permitted vehicle that exceeds 17 feet in height; and
(B) a front and rear escort flag vehicle for any permitted vehicle exceeding 18 feet in height.
(5) Escort requirements for permitted vehicles exceeding legal limits in more than one dimension. When a load exceeds more than one dimension that requires an escort under this subsection, front and rear escort flag vehicles will be required unless an exception is granted by TxDOT.
(6) Escort requirements for convoys. Convoys must have a front escort flag vehicle and a rear escort flag vehicle on all highways at all times.
(7) General equipment requirements. The following special equipment requirements apply to permitted vehicles and escort flag vehicles that are not motorcycles.
(A) An escort flag vehicle must be a single unit with a gross vehicle weight (GVW) of not less than 1,000 pounds nor more than 10,000 pounds.
(B) An escort flag vehicle must be equipped with two flashing amber lights; one rotating amber beacon of not less than eight inches in diameter; or alternating or flashing blue and amber lights, each of which must be visible from all directions while actively engaged in escort duties for the permitted vehicle.
(C) An escort flag vehicle must display a sign, on either the roof of the vehicle, or the front and rear of the vehicle, with the words "OVERSIZE LOAD" or "WIDE LOAD." The sign must be visible from the front and rear of the vehicle while escorting the permitted load. The sign must meet the following specifications:
(i) at least five feet, but not more than seven feet in length, and at least 12 inches, but not more than 18 inches in height;
(ii) the sign must have a yellow background with black lettering;
(iii) letters must be at least eight inches, but not more than 10 inches high with a brush stroke at least 1.41 inches wide; and
(iv) the sign must be visible from the front or rear of the vehicle while escorting the permitted vehicle, and the signs must not be used at any other time.
(D) An escort flag vehicle must maintain two-way communications with the permitted vehicle and other escort flag vehicles involved with the movement of the permitted vehicle.
(8) Equipment requirements for motorcycles.
(A) An official law enforcement motorcycle may be used as a primary escort flag vehicle for a permitted vehicle traveling within the limits of an incorporated city, if the motorcycle is operated by a highway patrol officer, sheriff, or duly authorized deputy, or municipal police officer.
(B) An escort flag vehicle must maintain two-way communications with the permitted vehicle and other escort flag vehicles involved with the movement of the permitted vehicle.
(l) Restrictions.
(1) Daytime and nighttime movement restrictions.
(A) A permitted vehicle may be moved only during the daytime unless:
(i) the permitted vehicle is overweight only;
(ii) the permitted vehicle is traveling on an interstate highway and does not exceed 10 feet wide and 100 feet long, with front and rear overhang that complies with legal standards; or
(iii) the permitted vehicle meets the criteria of clause (ii) of this subparagraph and is overweight.
(B) An exception may be granted allowing nighttime movement, based on a route and traffic study conducted by TxDOT. Escort flag vehicles may be required when an exception allowing nighttime movement is granted.
(2) Holiday restrictions.
(A) Effective through January 10, 2025, the maximum size limits for a permit issued under Transportation Code, Chapter 623, Subchapter D, for holiday movement is 14 feet wide, 16 feet high, and 110 feet long, unless an exception is granted based on a route and traffic study conducted by TxDOT.
(B) The department may restrict holiday movement of specific loads based on TxDOT’s determination that the load could pose a hazard for the traveling public due to local road or traffic conditions.
(3) Curfew restrictions. The operator of a permitted vehicle must observe the curfew movement restrictions published by the department.
(m) General provisions.
(1) Multiple commodities.
(A) When a permitted commodity creates a single overdimension, two or more commodities may be hauled as one permit load, provided legal axle weight and gross weight are not exceeded, and provided an overdimension of width, length or height is not created or made greater by the additional commodities. For example, a permit issued for the movement of a 12 foot wide storage tank may also include a 10 foot wide storage tank loaded behind the 12 foot wide tank provided that legal axle weight and gross weight are not exceeded, and provided an overdimension of width, length or height is not created.
(B) Subject to the restrictions in subparagraph (A) of this paragraph and the definition of a “nondivisible load or vehicle” in §219.2 of this title (relating to Definitions), an applicant requesting a permit to haul a dozer and its detached blade may be issued a permit, as a nondivisible load, if removal of the blade will decrease the overall width of the load, thereby reducing the hazard to the traveling public.
(2) Oversize hauling equipment. A vehicle that exceeds the legal size limits, as set forth by Transportation Code, Chapter 621, Subchapter C, may only haul a load that exceeds legal size limits unless otherwise noted in this subchapter, but such vehicle may haul an overweight load that does not exceed legal size limits, except for the special exception granted in §219.13(c)(3) of this title (relating to Time Permits).
(n) Surety bonds under Transportation Code, §623.075.
(1) General requirements. The surety bond must comply with the following requirements:
(A) be in the amount of $10,000;
(B) be filed on a form and in a manner prescribed by the department;
(C) be effective the day it is issued and expire at the end of the state fiscal year;
(D) include the primary mailing address and zip code of the principal;
(E) be signed by the principal; and
(F) have a single entity as principal with no other principal names listed.
(2) Non-resident agent. A non-resident agent with a valid Texas insurance license may issue a surety bond on behalf of an authorized insurance company when in compliance with Insurance Code, Chapter 4056.
(3) Certificate of continuation. A certificate of continuation will not be accepted.
(4) Electronic copy of surety bond. The department will accept an electronic copy of the surety bond in lieu of the original surety bond.
§219.12. Single-Trip Permits Issued Under Transportation Code, Chapter 623, Subchapter D.
(a) General. The information in this section applies to single-trip permits issued under Transportation Code, Chapter 623, Subchapter D. The department will issue permits under this section in accordance with the requirements of §219.11 of this title (relating to General Oversize/Overweight Permit Requirements and Procedures).
(b) Overweight loads.
(1) The maximum weight limits for an overweight permit are specified in §219.11(d).
(2) The applicant shall pay, in addition to the single-trip permit fee of $60, the applicable highway maintenance fee.
(3) The applicant must also pay the vehicle supervision fee (VSF) for a permit issued for an overweight vehicle and load exceeding 200,000 pounds gross weight.
(A) The VSF is $35 if:
(i) the vehicle and load do not exceed 254,300 pounds gross weight;
(ii) there is at least 95 feet of overall axle spacing; and
(iii) the vehicle and load do not exceed maximum permit weight on any axle or axle group, as described in §219.11(d).
(B) The VSF is $500 if:
(i) there is less than 95 feet of overall axle spacing;
(ii) the vehicle and load exceed maximum permit weight on any axle or axle group, as described in §219.11(d); or
(iii) the vehicle and load exceed 254,300 pounds gross weight. However, for a vehicle and load described in this subparagraph, the VSF is reduced from $500 to $100 if no bridges are crossed, and the VSF is reduced from $500 to $35 for an additional identical load that is to be moved over the same route within 30 days of the movement date of the original permit.
(C) An applicant must pay the VSF at the time of permit application in order to offset TxDOT’s costs for analyses performed in advance of issuing the permit. A request for cancellation must be in writing and received by the department prior to collection of the structural information associated with the permit application. If the application is canceled, the department will return the vehicle supervision fee.
(4) An applicant applying for a permit to move a load that is required for the fulfillment of a fixed price public works contract that was entered into prior to the effective date of this section, and administered by federal, state, or local governmental entities, will not be required to pay the vehicle supervision fee, provided the applicant presents proof of the contract to the department prior to permit issuance.
(5) When the department has determined that a permit can be issued for an overdimension load exceeding 200,000 pounds gross weight, all remaining fees are due at the time the permit is issued.
(6) Unless the permit is issued for a load under subsection (c) of this section, this permit may not be used for a container, including a trailer, loaded with divisible cargo.
(7) The following provisions apply to an application for a superheavy permit to move an overdimension load that is over 254,300 pounds gross weight, between 200,001 and 254,300 pounds gross weight with less than 95 feet overall axle spacing, or over the maximum permitted weight on any axle or axle group described in §219.11(d) of this title.
(A) In consultation with TxDOT and the applicant as necessary, the department will determine a tentative route based on the physical size of the overdimension load excluding the weight. After the department provides the tentative route to the applicant, the applicant must investigate the tentative route and acknowledge in writing to the department that the tentative route is capable of accommodating the overdimension load. If the applicant tells the department that the tentative route is not capable of accommodating the overdimension load, the department will consult with TxDOT and the applicant as necessary to attempt to create a tentative route that the applicant can acknowledge is capable of accommodating the overdimension load.
(B) The applicant must provide the department with the name and email address of the applicant’s TxDOT-certified, licensed professional engineering firm, which TxDOT certifies under Chapter 28, Subchapter G of this title (relating to Oversize and Overweight Vehicles and Loads). Once the applicant provides the department with the name and email address of the applicant’s TxDOT-certified, licensed professional engineering firm and acknowledges to the department that the tentative route is capable of accommodating the overdimension load, the department will provide the tentative route and the applicant’s application information to the applicant’s TxDOT-certified, licensed professional engineering firm.
(C) The applicant must provide information and documents, as requested, to the applicant’s TxDOT-certified, licensed professional engineering firm to enable the engineering firm to provide TxDOT with a written report under §28.86 of this title (relating to Bridge Report).
(D) Before the superheavy permit may be issued, the applicant's TxDOT-certified, licensed professional engineering firm must provide TxDOT with a written report that includes a detailed structural analysis of the bridges on the tentative route, demonstrating that the bridges and culverts on the tentative route are capable of sustaining the load. The department will not issue a superheavy permit unless TxDOT provides the department with approval for the tentative route proposed by the department and acknowledged by the applicant as capable of accommodating the overdimension load.
(c) Drill pipe and drill collars hauled in a pipe box.
(1) A vehicle or combination of vehicles may be issued a permit under Transportation Code, §623.071, to haul drill pipe and drill collars in a pipe box.
(2) The maximum width must not exceed 10 feet.
(3) The axle weight limits must not exceed the maximum weight limits as specified in §219.11(d)(3).
(4) The height and length must not exceed the legal limits specified in Transportation Code, Chapter 621, Subchapter C.
(5) The permit will be issued for a single-trip only. For loads over 80,000 pounds, the applicant must pay the single-trip permit fee, in addition to the highway maintenance fee specified in Transportation Code, §623.077.
(6) The permit is valid only for travel on any farm-to-market and ranch-to-market road, and such road will be specified on the permit; however, the permitted vehicle will not be allowed to cross any load restricted bridge when exceeding the posted capacity of the bridge.
(7) Movement will be restricted to daytime only.
(d) Houses.
(1) The issuance of a permit for a house exceeding 20 feet in width will be based on:
(A) the amount of inconvenience and hazard to the traveling public, based on traffic volume;
(B) highway geometrics and time of movement; and
(C) the overall width, measured to the nearest inch, of the house, including the eaves or porches.
(2) The proposed route must include the beginning and ending points on a state highway.
(3) A permit may be issued for the movement of an overweight house provided:
(A) the applicant provides the department with the requested information regarding weights;
(B) each support beam, parallel to the centerline of the highway, is equipped with an identical number of two-axle groups which may be placed directly in line and across from the other corresponding two-axle group or may be placed in a staggered offset arrangement to provide for proper weight distribution;
(C) that, when a support beam is equipped with two or more two-axle groups, each two-axle group is connected to a common mechanical or hydraulic system to ensure that each two-axle group shares equally in the weight distribution at all times during the movement; and when the spacing between the two-axle groups, measured from the center of the last axle of the front group to the center of the first axle of the following group, is eight feet or more, the front two-axle group is equipped for self-steering in a manner that will guide or direct the axle group in turning movements without tire scrubbing or pavement scuffing; and
(D) the department conducts a detailed analysis of each structure on the proposed route and determines the load can be moved without damaging the roads and bridges.
(e) Self-propelled off-road equipment. A permit may be issued for the movement of oversize and overweight self-propelled off-road equipment under the following conditions.
(1) The weight per inch of tire width must not exceed 650 pounds.
(2) The rim diameter of each wheel must be a minimum of 25 inches.
(3) The maximum weight per axle must not exceed 45,000 pounds.
(4) The minimum spacing between axles, measured from center of axle to center of axle, must not be less than 12 feet.
(5) The equipment must be moved empty.
(6) The route will not include any controlled access highway, unless an exception is granted based on a route and traffic study conducted by TxDOT.
§219.13. Time Permits.
(a) General information. Applications for time permits issued under Transportation Code, Chapter 622 and Chapter 623, and this section shall be made in accordance with §219.11(b) and (c) of this title (relating to General Oversize/Overweight Permit Requirements and Procedures). Permits issued under this section are governed by the requirements of §219.11(e)(1) of this title.
(b) 30, 60, and 90 day permits. The following conditions apply to time permits issued for overwidth or overlength loads, or overlength vehicles, under this section.
(1) Validity of Permit. Time permits are valid for a period of 30, 60, or 90 calendar days, based on the request of the applicant, and will begin on the effective date stated on the permit.
(2) Weight/height limits. The permitted vehicle may not exceed the weight or height limits set forth by Transportation Code, Chapter 621, Subchapters B and C.
(3) Vehicle indicated on permit. The permit will indicate only the truck or truck-tractor transporting the load; however, any properly registered trailer or semi-trailer is covered by the permit.
(4) Permit routes. The permit will allow travel on a statewide basis.
(5) Restrictions.
(A) The permitted vehicle must not cross a load restricted bridge or load restricted road when exceeding the posted capacity of the road or bridge.
(B) The permitted vehicle may travel through highway construction or maintenance areas if the dimensions do not exceed the construction restrictions as published by the department.
(C) The permitted vehicle is subject to the restrictions specified in §219.11(l) of this title, and the permittee is responsible for obtaining from the department information concerning current restrictions.
(6) Escort requirements. Permitted vehicles are subject to the escort requirements specified in §219.11(k) of this title.
(7) Transfer of time permits. Time permits issued under this subsection are non-transferable between permittees or vehicles.
(8) Amendments. With the exception of time permits issued under subsection (e)(4) of this section, time permits issued under this subsection will not be amended except in the case of permit officer error.
(c) Overwidth loads. An overwidth time permit may be issued for the movement of any load or overwidth trailer, subject to subsection (a) of this section and the following conditions:
(1) Width requirements.
(A) A time permit will not be issued for a vehicle with a width exceeding 13 feet.
(B) When multiple items are hauled at the same time, the items may not be loaded in a manner that creates a width greater than the width of the widest item being hauled.
(2) Weight, height, and length requirements.
(A) The permitted vehicle shall not exceed legal weight, height, or length according to Transportation Code, Chapter 621, Subchapters B and C.
(B) When multiple items are hauled at the same time, the items may not be loaded in a manner that creates:
(i) a height greater than 14 feet;
(ii) an overlength load; or
(iii) a gross weight exceeding the legal gross or axle weight of the vehicle hauling the load.
(3) Movement of overwidth trailers. When the permitted vehicle is an overwidth trailer, it will be allowed to:
(A) move empty to and from the job site; and
(B) haul a load from the permitted vehicle's point of origin to pick up a permitted load, and to the permitted vehicle's point of origin or the permittee's place of business after dropping off a permitted load, as long as:
(i) the load does not exceed legal size and weight limits under Transportation Code, Chapters 621 and 622; and
(ii) the transport complies with the permit, including the time period stated on the permit.
(4) Use in conjunction with other permits. An overwidth time permit may be used in conjunction with an overlength time permit.
(d) Overlength loads. An overlength time permit may be issued for the transportation of overlength loads or the movement of an overlength self-propelled vehicle, subject to subsection (a) of this section and the following conditions:
(1) Length requirements.
(A) The maximum overall length for the permitted vehicle may not exceed 110 feet.
(B) The department may issue a permit under Transportation Code, §623.071(a) for an overlength load or an overlength self-propelled vehicle that falls within the definition of a nondivisible load or vehicle.
(2) Weight, height and width requirements.
(A) The permitted vehicle may not exceed legal weight, height, or width according to Transportation Code, Chapter 621, Subchapters B and C.
(B) A permit will not be issued when the load has more than 25 feet front overhang, or more than 30 feet rear overhang.
(3) Use in conjunction with other permits. An overlength time permit may be used in conjunction with an overwidth time permit.
(4) Emergency movement. A permitted vehicle transporting utility poles will be allowed emergency nighttime movement for restoring electrical utility service, provided the permitted vehicle is accompanied by a rear escort flag vehicle.
(e) Annual permits.
(1) General information. All permits issued under this subsection are subject to the following conditions.
(A) Permits issued under this subsection are not transferable.
(B) Vehicles permitted under this subsection shall be operated according to the restrictions described in §219.11(l) of this title. The permittee is responsible for obtaining information concerning current restrictions from the department.
(C) Vehicles permitted under this subsection may not travel over a load restricted bridge or load restricted road when exceeding the posted capacity of the road or bridge.
(D) Vehicles permitted under this subsection may travel through any highway construction or maintenance area provided the dimensions do not exceed the construction restrictions as published by the department.
(E) With the exception of permits issued under paragraph (5) of this subsection, vehicles permitted under this subsection shall be operated according to the escort requirements described in §219.11(k) of this title.
(2) Implements of husbandry. An annual permit may be issued for an implement of husbandry being moved by a dealer in those implements, and for harvesting equipment being moved as part of an agricultural operation. Permits issued under this paragraph are subject to the conditions described in paragraph (1) of this subsection.
(A) The fee for a permit issued under this paragraph is $270, plus the highway maintenance fee specified in Transportation Code, §623.077.
(B) The time period will be for one year and will start on the effective date stated on the permit.
(C) The maximum width may not exceed 16 feet; maximum height may not exceed 16 feet; maximum length may not exceed 110 feet; and maximum weight may not exceed the limits stated in §219.11(d) of this title.
(D) Unless stated otherwise on the permit, the permitted vehicle must travel in the outside traffic lane on multi-lane highways, when the width of the load exceeds 12 feet.
(E) The permitted vehicle must be registered in accordance with Transportation Code, Chapter 502, for maximum weight for the vehicle or vehicle combination, as set forth by Transportation Code, Chapter 621.
(3) Water well drilling machinery. The department may issue annual permits under Transportation Code, §623.071, for water well drilling machinery and equipment that fall within the definition of a nondivisible load or vehicle. Permits issued under this paragraph are subject to the conditions described in paragraph (1) of this subsection.
(A) The fee for a permit issued under this paragraph is $270, plus the highway maintenance fee specified in Transportation Code, §623.077 for an overweight load.
(B) A water well drilling machinery permit is valid for one year from the effective date stated on the permit.
(C) The maximum dimensions may not exceed 16 feet wide, 14 feet 6 inches high, 110 feet long, and maximum weight may not exceed the limits stated in §219.11(d) of this title.
(D) The permitted vehicle must be registered in accordance with Transportation Code, Chapter 502, for the maximum weight of the vehicle, as set forth by Transportation Code, Chapter 621.
(E) A permit issued under this section authorizes a permitted vehicle to operate only on the state highway system.
(4) Envelope vehicle permits.
(A) The department may issue an annual permit under Transportation Code, §623.071(c), to a specific vehicle, for the movement of superheavy or oversize equipment that falls within the definition of a nondivisible load. This permit may not be used for a container, including a trailer, loaded with divisible cargo. Unless otherwise noted, permits issued under this paragraph are subject to the conditions described in paragraph (1) of this subsection.
(i) Superheavy or oversize equipment operating under an annual envelope vehicle permit may not exceed:
(I) 12 feet in width;
(II) 14 feet in height;
(III) 110 feet in length; or
(IV) 120,000 pounds gross weight.
(ii) Superheavy or oversize equipment operating under an annual envelope vehicle permit may not transport a load that has more than 25 feet front overhang, or more than 30 feet rear overhang.
(iii) The fee for an annual envelope vehicle permit is $4,000, and is non-refundable.
(iv) The time period will be for one year and will start on the effective date stated on the permit.
(v) This permit authorizes operation of the permitted vehicle only on the state highway system.
(vi) The permitted vehicle must comply with §219.11(d)(2) and (3) of this title.
(vii) The permitted vehicle or vehicle combination must be registered in accordance with Transportation Code, Chapter 502, for maximum weight as set forth by Transportation Code, Chapter 621.
(viii) A permit issued under this paragraph is non-transferable between permittees.
(ix) A permit issued under this paragraph may be transferred from one vehicle to another vehicle in the permittee's fleet provided:
(I) the permitted vehicle is destroyed or otherwise becomes permanently inoperable, to an extent that it will no longer be utilized, and the permittee presents proof that the negotiable certificate of title or other qualifying documentation has been surrendered to the department; or
(II) the certificate of title to the permitted vehicle is transferred to someone other than the permittee, and the permittee presents proof that the negotiable certificate of title or other qualifying documentation has been transferred from the permittee.
(x) A single-trip permit, as described in §219.12 of this title (relating to Single-Trip Permits Issued Under Transportation Code, Chapter 623, Subchapter D), may be used in conjunction with an annual permit issued under this paragraph for the movement of vehicles or loads exceeding the height or width limits established in subparagraph (A) of this paragraph. The department will indicate the annual permit number on any single-trip permit to be used in conjunction with a permit issued under this paragraph, and permittees will be assessed a fee of $60 for the single-trip permit.
(B) The department may issue an annual permit under Transportation Code, §623.071(d), to a specific motor carrier, for the movement of superheavy or oversize equipment that falls within the definition of a nondivisible load. This permit may not be used for a container, including a trailer, loaded with divisible cargo. Unless otherwise noted, permits issued under this paragraph are subject to the conditions described in paragraph (1) of this subsection and subparagraphs (A)(i)-(viii) of this paragraph. A permit issued under this paragraph may be transferred from one vehicle to another vehicle in the permittee's fleet provided:
(i) that no more than one vehicle is operated at a time; and
(ii) the original certified permit is carried in the vehicle that is being operated under the terms of the permit.
(C) An annual envelope permit issued under subparagraph (B) of this paragraph will be sent to the permittee via registered mail, or at the permittee's request and expense overnight delivery service. This permit may not be duplicated. This permit will be replaced only if:
(i) the permittee did not receive the original permit within seven business days after its date of issuance;
(ii) a request for replacement is submitted to the department within 10 business days after the original permit's date of issuance; and
(iii) the request for replacement is accompanied by a notarized statement signed by a principal or officer of the permittee acknowledging that the permittee understands the permit may not be duplicated and that if the original permit is located, the permittee must return either the original or replacement permit to the department.
(D) A request for replacement of a permit issued under subparagraph (B) of this paragraph will be denied if the department can verify that the permittee received the original.
(E) Lost, misplaced, damaged, destroyed, or otherwise unusable permits will not be replaced. A new permit will be required.
(5) Annual manufactured housing permit. The department may issue an annual permit for the transportation of new manufactured homes from a manufacturing facility to a temporary storage location, not to exceed 20 miles from the point of manufacture, in accordance with Transportation Code, §623.094. Permits issued under this paragraph are subject to the requirements of paragraph (1), subparagraphs (A), (B), (C), and (D) of this subsection.
(A) A permit shall contain the name of the company or person authorized to be issued permits by Transportation Code, Chapter 623, Subchapter E.
(B) The fee for a permit issued under this paragraph is $1,500. Fees are non-refundable.
(C) The time period will be for one year from the effective date stated on the permit.
(D) The permitted vehicle must travel in the outside traffic lane on multi-lane highways when the width of the load exceeds 12 feet.
(E) Authorized movement for a vehicle permitted under this section shall be valid during daytime only.
(F) Permits issued under this section are non-transferable between permittees.
(6) Power line poles. An annual permit will be issued under Transportation Code, Chapter 622, Subchapter E, for the movement of poles required for the maintenance of electric power transmission and distribution lines. Permits issued under this paragraph are subject to the conditions described in paragraph (1) of this subsection.
(A) The fee for the permit is $120.
(B) The time period will be for one year and will start on the effective date stated on the permit.
(C) The maximum length of the permitted vehicle may not exceed 75 feet.
(D) The width, height and gross weight of the permitted vehicle may not exceed the limits set forth by Transportation Code, Chapter 621.
(E) Vehicles permitted under this paragraph may not travel over a load restricted bridge or load zoned road when exceeding posted limits.
(F) Movement will be between the hours of sunrise and sunset; however, the limitation on hours of operation does not apply to a vehicle being operated to prevent interruption or impairment of electric service, or to restore electric service that has been interrupted. When operated at nighttime, a vehicle permitted under this subsection must be accompanied by a rear escort flag vehicle.
(G) The speed of the permitted vehicle may not exceed 50 miles per hour.
(H) The permitted vehicle must display on the extreme end of the load:
(i) two red lamps visible at a distance of at least 500 feet from the rear;
(ii) two red reflectors that indicate the maximum width and are visible, when light is insufficient or atmospheric conditions are unfavorable, at all distances from 100 to 600 feet from the rear when directly in front of lawful lower beams of headlamps; and
(iii) two red lamps, one on each side, that indicate the maximum overhang, and are visible at a distance of at least 500 feet from the side of the vehicle.
(7) Cylindrically shaped bales of hay. An annual permit may be issued under Transportation Code, §623.017, for the movement of vehicles transporting cylindrically shaped bales of hay. Permits issued under this paragraph are subject to the conditions described in paragraph (1) of this subsection.
(A) The permit fee is $10.
(B) The time period will be for one year, and will start on the effective date stated on the permit.
(C) The maximum width of the permitted vehicle may not exceed 12 feet.
(D) The length, height, and gross weight of the permitted vehicle may not exceed the limits set forth by Transportation Code, Chapter 621.
(E) Movement is restricted to daytime only.
(8) Overlength load or vehicles. An annual overlength permit may be issued for the transportation of a nondivisible overlength load or the movement of a nondivisible overlength vehicle or combination of vehicles under Transportation Code, §623.071(c-1). This permit is subject to the portions of subsections (a), (b), and (d) of this section that are not limited to the duration for the 30, 60, and 90 day permits.
§219.14. Manufactured Housing, and Industrialized Housing and Building Permits.
(a) General Information.
(1) A manufactured home that exceeds size limits for motor vehicles as defined by Transportation Code, Chapter 621, Subchapters B and C, must obtain a permit from the department.
(2) Pursuant to Transportation Code, Chapter 623, Subchapter E, a permit may be issued to persons registered as manufacturers, installers, or retailers with the Texas Department of Housing and Community Affairs or motor carriers registered with the department under Transportation Code, Chapter 643.
(3) The department may issue a permit to the owner of a manufactured home provided that:
(A) the same owner is named on the title of the manufactured home and towing vehicle;
(B) or the owner presents a lease showing that the owner of the manufactured home is the lessee of the towing vehicle.
(b) Permit application.
(1) To qualify for a permit under this section, a person must submit an application to the department.
(2) All applications shall be made in a form and by the method prescribed by the department, and at a minimum shall include the following:
(A) name, customer identification number, and address of the applicant;
(B) name, telephone number, and email address of contact person;
(C) applicant's USDOT Number if applicant is required by law to have a USDOT Number;
(D) complete description of the manufactured home, including the year, make and one of the following:
(i) manufactured home's HUD label number;
(ii) Texas seal number; or
(iii) the complete identification number or serial number;
(E) the maximum width, height and length of the vehicle and manufactured home; and
(F) any other information required by law, including the information listed in Transportation Code §623.093(a).
(c) Amendments to permit. Amendments can only be made to change intermediate points between the origination and destination points listed on the permit.
(d) Permit provisions and conditions.
(1) The overall combined length of the manufactured home and the towing vehicle includes the length of the hitch or towing device.
(2) The height is measured from the roadbed to the highest elevation of the manufactured home.
(3) The width of a manufactured home includes any roof or eaves extension or overhang on either side.
(4) A permit will be issued for a single continuous movement not to exceed five days.
(5) The department may limit the hours for travel on certain routes because of heavy traffic conditions.
(6) The department will publish any limitations on movements during the national holidays, or any limitations during certain hours of heavy traffic conditions, and will make such publications available to the public prior to the limitations becoming effective.
(7) The permit will contain the route for the transportation of the manufactured home from the point of origin to the point of destination.
(8) The route for the transportation must be the most practical route as described in §219.11(e) of this title (relating to General Oversize/Overweight Permit Requirements and Procedures), except where construction is in progress and the permitted vehicle's dimensions exceed the construction restrictions as published by the department, or where bridge or overpass width or height would create a safety hazard.
(9) A permittee may not transport a manufactured home with a void permit; a new permit must be obtained.
§219.15. Portable Building Unit Permits.
(a) General information.
(1) A vehicle or vehicle combination transporting one or more portable building units and portable building compatible cargo that exceed legal length or width limits set forth by Transportation Code, Chapter 621, Subchapters B and C, may obtain a permit under Transportation Code, Chapter 623, Subchapter F.
(2) In addition to the fee required by statute, the department shall collect an amount equal to any fee that would apply to the movement of cargo exceeding any applicable width limits, if such cargo were moved in a manner not governed by this section.
(b) Application for permit. Applications shall be made in accordance with §219.11(c) of this title (relating to General Oversize/Overweight Permit Requirements and Procedures).
(c) Permit issuance. Permit issuance is subject to the requirements of §219.11(e) and (g) of this title.
(d) Non-refundable permit fee. All fees are non-refundable.
(e) Permit provisions and conditions.
(1) A portable building unit may only be issued a single-trip permit.
(2) Portable building units may be loaded end-to-end to create an overlength permit load, provided the overall length does not exceed 80 feet.
(3) Portable building units must not be loaded side-by-side to create an overwidth load, or loaded one on top of another to create an overheight load.
(4) Portable building units must be loaded in a manner that will create the narrowest width for permit purposes and provide for greater safety to the traveling public.
(5) The permit will be issued for a single continuous movement from the origin to the destination for an amount of time necessary to make the move, not to exceed 10 consecutive days.
(6) Movement of the permitted vehicle must be made during daytime only.
(7) A permittee may not transport portable building units or portable building compatible cargo with a void permit; a new permit must be obtained.
Subchapter C. Permits for Over Axle and Over Gross Weight Tolerances
§219.30. Permits for Over Axle and Over Gross Weight Tolerances.
(a) Purpose. In accordance with Transportation Code, §623.011, the department is authorized under certain conditions to issue an annual permit for the operation of a vehicle within certain tolerances above legal axle and gross weight limits, as provided in Transportation Code, Chapter 621.
(b) Scope. A permit may be issued to an applicant under this section to operate a vehicle that exceeds the legal axle weight by a tolerance of 10% and the legal gross weight by a tolerance of 5.0% on any county road and on any road in the state highway system provided the vehicle:
(1) is not operated on the national system of interstate and defense highways at a weight greater than authorized by federal law; and
(2) is not operated on a bridge for which the maximum weight and load limit has been established and posted under Transportation Code, §621.102 or §621.301, if the gross weight of the vehicle and load or the axles and wheel loads are greater than the established and posted limits, unless the bridge provides the only public vehicular access to or from the permittee's origin or destination.
(c) Application for permit.
(1) To qualify for a permit under this section, a person must submit an application to the department.
(2) The application shall be in a form prescribed by the department and at a minimum will require the following:
(A) name, customer identification number, and address of the applicant;
(B) name, telephone number, and email address of contact person;
(C) vehicle information, including truck year, make, license plate number and state of issuance, and vehicle identification number;
(D) an indication as to whether the commodities to be transported will be agricultural or non-agricultural;
(E) a list of counties in which the vehicle will operate; and
(F) applicant's USDOT Number if applicant is required by law to have a USDOT Number.
(3) The application shall be accompanied by:
(A) the total permit fee, which includes an administrative fee of $5, the base fee, and the applicable annual fee based on the number of counties designated for travel; and
(B) an original bond or irrevocable letter of credit as required in Transportation Code §623.012.
(d) Issuance of permit and windshield sticker.
(1) A permit and a windshield sticker will be issued on the approval of the application and each will be mailed to the applicant at the address contained in the application.
(2) The permit shall be carried in the vehicle for which the permit is issued at all times.
(3) The windshield sticker shall be affixed to the inside of the windshield of the vehicle in accordance with the diagram printed on the back of the sticker in a manner that will not obstruct the vision of the driver. Any attempt to remove the sticker from the windshield will render the sticker void, and will require a new permit and sticker. The windshield sticker must be removed from the vehicle upon expiration of the permit.
(4) A replacement sticker for a lost, stolen, or mutilated windshield sticker may be issued, provided that the permittee submits a request on a form approved by the department which shall include a statement, signed by the permittee, affirming that the sticker was lost, stolen, or mutilated. The replacement sticker shall only be valid for the permitted vehicle. The cost for a replacement sticker is $3.00.
(e) Issuance of a credit. Upon written application on a form prescribed by the department, a prorated credit for the remaining time on the permit may be issued for a vehicle that is destroyed or otherwise becomes permanently inoperable to an extent that it will no longer be utilized. The date for computing a credit will be based on the date of receipt of the credit request. The fee for a credit will be $25, and will be issued on condition that the applicant provides to the department:
(1) the original permit; or
(2) if the original permit no longer exists, written evidence of the destruction or permanent incapacity from the insurance carrier of the vehicle.
(f) Use of credit. A credit issued under subsection (e) of this section may be used only towards the payment of permit fees under this section.
(g) Lapse or termination of permit. A permit shall lapse or terminate and the windshield sticker must be removed from the vehicle:
(1) when the lease of the vehicle expires;
(2) on the sale of the vehicle for which the permit was issued;
(3) on the sale, takeover, or dissolution of the firm, partnership, or corporation to which a permit was issued; or
(4) if the permittee does not replace or replenish the letter of credit or bond as required by Transportation Code, §623.012.
§219.31. Timber Permits.
(a) Purpose. This section prescribes the requirements and procedures regarding the annual permit for the operation of a vehicle or combination of vehicles that will be used to transport unrefined timber, wood chips, woody biomass, or equipment used to load timber on a vehicle under the provisions of Transportation Code, Chapter 623, Subchapter Q.
(b) Application for permit.
(1) To qualify for a timber permit, a person must submit an application to the department.
(2) The application shall be in a form prescribed by the department and at a minimum, will require the following:
(A) name, customer identification number, and address of the applicant;
(B) name, telephone number, and email address of contact person;
(C) vehicle information, including vehicle year, make, license plate number and state of issuance, and vehicle identification number;
(D) a list of timber producing counties described in Transportation Code, §623.321(a), in which the vehicle or combination of vehicles will be operated; and
(E) applicant's USDOT Number if applicant is required by law to have a USDOT Number.
(3) The application shall be accompanied by:
(A) the total annual permit fee required by statute; and
(B) a blanket bond or irrevocable letter of credit as required by Transportation Code, §623.012, unless the applicant has a current blanket bond or irrevocable letter of credit on file with the department that complies with Transportation Code, §623.012.
(c) Issuance and placement of permit and windshield sticker; restrictions.
(1) A permit and a windshield sticker will be issued once the application is approved, and each will be mailed to the applicant at the address contained in the application.
(2) The windshield sticker shall be affixed to the inside of the windshield of the vehicle in accordance with the diagram printed on the back of the sticker and in a manner that will not obstruct the vision of the driver. Any attempt to remove the sticker from the windshield will render the sticker void and will require a new permit and sticker.
(3) A replacement sticker for a lost, stolen, or mutilated windshield sticker may be issued, provided that the permittee submits a request on a form approved by the department which shall include a statement, signed by the permittee, affirming that the sticker was lost, stolen, or mutilated. The replacement sticker shall only be valid for the permitted vehicle.
(d) Notification. The financially responsible party as defined in Transportation Code, §623.323(a), shall electronically file the notification document described by §623.323(b) with the department via the form on the department's website.
(e) Transfer of permit. An annual permit issued under this section is not transferable between vehicles.
(f) Amendments. An annual permit issued under this section will not be amended except in the case of department error.
(g) Termination of permit. An annual permit issued under this section will automatically terminate, and the windshield sticker must be removed from the vehicle:
(1) on the expiration of the permit;
(2) when the lease of the vehicle expires;
(3) on the sale or other transfer of ownership of the vehicle for which the permit was issued;
(4) on the dissolution or termination of the partnership, corporation, or other legal entity to which the permit was issued; or
(5) if the permittee fails to timely replenish the bond or letter of credit as required by Transportation Code, §623.012.
(h) Restrictions. Permits issued under this section are subject to the restrictions in §219.11(l) of this title.
§219.32. Ready-Mixed Concrete Truck Permits.
(a) Purpose. This section prescribes the requirements, restrictions, and procedures regarding the annual permit for a ready-mixed concrete truck, operating on three axles, under the provisions of Transportation Code, §623.0171 and Chapter 622, Subchapter B.
(b) Axles. To qualify for movement with a ready-mixed concrete truck permit, the truck may only operate on three axles, regardless of whether the truck actually has more than three axles.
(c) Application for permit.
(1) To qualify for a ready-mixed concrete truck permit, a person must submit an application to the department.
(2) The application shall be in a form prescribed by the department and at a minimum, will require the following:
(A) name, customer identification number, and address of the applicant;
(B) name, telephone number, and email address of contact person;
(C) vehicle information, including vehicle year, make, license plate number and state of issuance, and vehicle identification number;
(D) a list of counties in which the vehicle will be operated; and
(E) applicant's USDOT Number if applicant is required by law to have a USDOT Number.
(3) The application shall be accompanied by the total annual permit fee of $1,000.
(d) Issuance and placement of permit and windshield sticker; restrictions.
(1) A permit and a windshield sticker will be issued once the application is approved, and each will be mailed to the applicant at the address contained in the application.
(2) The windshield sticker shall be affixed to the inside of the windshield of the vehicle in accordance with the diagram printed on the back of the sticker and in a manner that will not obstruct the vision of the driver. Any attempt to remove the sticker from the windshield will render the sticker void and will require a new permit and sticker.
(3) A replacement sticker for a lost, stolen, or mutilated windshield sticker may be issued, provided that the permittee submits a request on a form approved by the department. The request shall include a statement, signed by the permittee, affirming that the sticker was lost, stolen, or mutilated. The replacement sticker shall only be valid for the permitted vehicle.
(e) Transfer of permit. An annual permit issued under this section is not transferable between vehicles.
(f) Amendments. An annual permit issued under this section will not be amended except in the case of department error.
(g) Termination of permit. An annual permit issued under this section will automatically terminate, and the windshield sticker must be removed from the vehicle:
(1) on the expiration of the permit;
(2) when the lease of the vehicle expires;
(3) on the sale or other transfer of ownership of the vehicle for which the permit was issued; or
(4) on the dissolution or termination of the partnership, corporation, or other legal entity to which the permit was issued.
(h) Curfew restrictions. The operator of a permitted vehicle must observe the curfew movement restrictions published by the department.
(i) Construction or maintenance areas.
(1) Permits issued under this section authorize the operator of the permitted vehicle to travel through any state highway construction or maintenance area, provided the size and weight of the vehicle do not exceed the construction restrictions that are available on the department's website. If a permitted vehicle is delivering concrete to a state highway construction or maintenance jobsite within a construction or maintenance area, the following may provide the permittee a written exception to operate the permitted vehicle in the construction or maintenance area at a size or weight that exceeds the size and weight listed on the department's website: the Texas Department of Transportation or a Texas Department of Transportation contractor that is authorized by the Texas Department of Transportation to issue permit exceptions. The written exception must be carried in the permitted vehicle when the vehicle is on a state highway and must be provided to the department or law enforcement upon request.
(2) The permittee is responsible for contacting the appropriate local jurisdiction for construction or maintenance restrictions on non-state maintained roadways.
(j) Manufacturer's tire load rating. Permits issued under this section do not authorize the vehicle to exceed the manufacturer's tire load rating.
(k) Distribution of fees. Fifty percent of the fees collected for permits under Transportation Code, §623.0171 shall be divided equally among all counties designated in the permit application.
§219.34. North Texas Intermodal Permit.
(a) Purpose. This section prescribes the requirements, restrictions, and procedures regarding the annual permit for transporting an intermodal shipping container under the provisions of Transportation Code, §623.0172.
(b) Application for permit.
(1) To qualify for a North Texas intermodal permit, a person must submit an application to the department.
(2) The application shall be in a form prescribed by the department and at a minimum, will require the following:
(A) name, customer identification number, and address of the applicant;
(B) name, telephone number, and email address of contact person;
(C) vehicle information, including vehicle year, make, license plate number and state of issuance, and vehicle identification number; and
(D) applicant’s USDOT Number if applicant is required by law to have a USDOT Number.
(3) The application shall be accompanied by the total annual permit fee of $1,000.
(c) Amendments. An annual permit issued under this section will not be amended except in the case of department error.
(d) Transfer of permit. A permit issued under this section may only be transferred once during the term of the permit from one vehicle to another vehicle in the permittee's fleet provided:
(1) the permitted vehicle is destroyed or otherwise becomes permanently inoperable, to an extent that it will no longer be utilized, and the permittee presents proof that the negotiable title or other qualifying documentation, as determined by the department, has been surrendered to the department; or
(2) the title to the permitted vehicle is transferred to someone other than the permittee, and the permittee presents proof that the negotiable title or other qualifying documentation, as determined by the department, has been transferred from the permittee.
(e) Curfew restrictions. The operator of a permitted vehicle must observe the curfew movement restrictions published by the department.
(f) Construction or maintenance areas. The permitted vehicle may not travel through any state highway construction or maintenance area if prohibited by the construction restrictions published by the department.
(g) Nighttime movement. Nighttime movement is allowed under this permit, unless prohibited by the curfew movement restrictions published by the department.
(h) Manufacturer's tire load rating. Permits issued under this section do not authorize the vehicle to exceed the manufacturer's tire load rating.
(i) A truck-tractor and semitrailer combination is only eligible for a permit issued under this section if the truck-tractor is equipped with truck blind spot systems, and each vehicle in the combination is equipped with a roll stability support safety system.
(j) A truck-tractor and semitrailer combination is only eligible for a permit issued under this section if the distance between the front axle of the truck-tractor and the last axle of the semitrailer, measured longitudinally, is approximately 647 inches. For the purposes of this subsection, "approximately 647 inches" means the distance can be up to 15 percent above 647 inches for a total distance of 744.05 inches.
§219.35. Fluid Milk Transport Permit.
(a) Purpose. This section prescribes the requirements, restrictions, and procedures regarding the annual permit for transporting fluid milk under the provisions of Transportation Code, Chapter 623, Subchapter V.
(b) Application for permit.
(1) To qualify for a fluid milk transport permit, a person must submit an application to the department.
(2) The application shall be in a form prescribed by the department and at a minimum, will require the following:
(A) name, customer identification number, and address of the applicant;
(B) name, telephone number, and email address of contact person;
(C) vehicle information, including vehicle year, make, license plate number and state of issuance, and vehicle identification number;
(D) a list of counties in which the vehicle will be operated; and
(E) applicant's USDOT Number if applicant is required by law to have a USDOT Number.
(3) The application shall be accompanied by the total annual permit fee of $1,200.
(c) Issuance and placement of permit and windshield sticker; restrictions.
(1) A permit and a windshield sticker will be issued once the application is approved, and each will be mailed to the applicant at the address contained in the application.
(2) The windshield sticker shall be affixed to the inside of the windshield of the vehicle in accordance with the diagram printed on the back of the sticker and in a manner that will not obstruct the vision of the driver. Any attempt to remove the sticker from the windshield will render the sticker void and will require a new permit and sticker.
(3) A replacement sticker for a lost, stolen, or mutilated windshield sticker may be issued, provided that the permittee submits a request on a form approved by the department which shall include a statement, signed by the permittee, affirming that the sticker was lost, stolen, or mutilated. The replacement sticker shall only be valid for the permitted vehicle.
(d) Amendments. An annual permit issued under this section will not be amended except in the case of department error.
(e) Transfer of permit. A permit issued under this section may only be transferred once during the term of the permit from one vehicle to another vehicle in the permittee's fleet provided:
(1) the permitted vehicle is destroyed or otherwise becomes permanently inoperable, to an extent that it will no longer be utilized, and the permittee presents proof that the negotiable title or other qualifying documentation, as determined by the department, has been surrendered to the department; or
(2) the title to the permitted vehicle is transferred to someone other than the permittee, and the permittee presents proof that the negotiable title or other qualifying documentation, as determined by the department, has been transferred from the permittee.
(f) Termination of permit. An annual permit issued under this section will automatically terminate, and the windshield sticker must be removed from the vehicle:
(1) on the expiration of the permit;
(2) when the lease of the vehicle expires;
(3) on the sale or other transfer of ownership of the vehicle for which the permit was issued; or
(4) on the dissolution or termination of the partnership, corporation, or other legal entity to which the permit was issued.
(g) Curfew restrictions. The operator of a permitted vehicle must observe the curfew movement restrictions published by the department.
(h) Construction or maintenance areas.
(1) The permitted vehicle may not travel through any state highway construction or maintenance area if prohibited by the construction restrictions published by the department.
(2) The permittee is responsible for contacting the appropriate local jurisdiction for construction or maintenance restrictions on non-state maintained roadways.
(i) Nighttime movement. Nighttime movement is allowed under this permit, unless prohibited by the curfew movement restrictions published by the department.
(j) Manufacturer's tire load rating. Permits issued under this section do not authorize the vehicle to exceed the manufacturer's tire load rating.
(k) A truck-tractor and semitrailer combination is only eligible for a permit issued under this section if the truck-tractor is equipped with truck blind spot systems, and each vehicle in the combination is equipped with a roll stability support safety system.
§219.36. Intermodal Shipping Container Port Permit.
(a) Purpose. This section prescribes the requirements, restrictions, and procedures regarding the annual permit for transporting an intermodal shipping container under the provisions of Transportation Code, Chapter 623, Subchapter U.
(b) Application for permit.
(1) To qualify for an intermodal shipping container port permit, a person must submit an application to the department.
(2) The application shall be in a form prescribed by the department and at a minimum, will require the following:
(A) name, customer identification number, and address of the applicant;
(B) name, telephone number, and email address of contact person;
(C) vehicle information, including vehicle year, make, license plate number and state of issuance, and vehicle identification number;
(D) a list of counties in which the vehicle will be operated;
(E) a list of municipalities in which the vehicle will be operated; and
(F) applicant's USDOT Number if applicant is required by law to have a USDOT Number.
(3) The application shall be accompanied by the total annual permit fee of $6,000.
(c) Issuance and placement of permit and windshield sticker; restrictions.
(1) A permit and a windshield sticker will be issued once the application is approved, and each will be mailed to the applicant at the address contained in the application.
(2) The windshield sticker shall be affixed to the inside of the windshield of the vehicle in accordance with the diagram printed on the back of the sticker and in a manner that will not obstruct the vision of the driver. Any attempt to remove the sticker from the windshield will render the sticker void and will require a new permit and sticker.
(3) A replacement sticker for a lost, stolen, or mutilated windshield sticker may be issued, provided that the permittee submits a request on a form approved by the department which shall include a statement, signed by the permittee, affirming that the sticker was lost, stolen, or mutilated. The replacement sticker shall only be valid for the permitted vehicle.
(d) Amendments. An annual permit issued under this section will not be amended except in the case of department error.
(e) Transfer of permit. A permit issued under this section may only be transferred once during the term of the permit from one vehicle to another vehicle in the permittee's fleet provided:
(1) the permitted vehicle is destroyed or otherwise becomes permanently inoperable, to an extent that it will no longer be utilized, and the permittee presents proof that the negotiable title or other qualifying documentation, as determined by the department, has been surrendered to the department; or
(2) the title to the permitted vehicle is transferred to someone other than the permittee, and the permittee presents proof that the negotiable title or other qualifying documentation, as determined by the department, has been transferred from the permittee.
(f) Termination of permit. An annual permit issued under this section will automatically terminate, and the windshield sticker must be removed from the vehicle:
(1) on the expiration of the permit;
(2) when the lease of the vehicle expires;
(3) on the sale or other transfer of ownership of the vehicle for which the permit was issued; or
(4) on the dissolution or termination of the partnership, corporation, or other legal entity to which the permit was issued.
(g) Curfew restrictions. The operator of a permitted vehicle must observe the curfew movement restrictions published by the department.
(h) Construction or maintenance areas.
(1) The permitted vehicle may not travel through any state highway construction or maintenance area if prohibited by the construction restrictions published by the department.
(2) The permittee is responsible for contacting the appropriate local jurisdiction for construction or maintenance restrictions on non-state maintained roadways.
(i) Nighttime movement. Nighttime movement is allowed under this permit, unless prohibited by the curfew movement restrictions published by the department.
(j) Manufacturer's tire load rating. Permits issued under this section do not authorize the vehicle to exceed the manufacturer's tire load rating.
(k) A truck-tractor and semitrailer combination is only eligible for a permit issued under this section if the truck-tractor is equipped with truck blind spot systems, and each vehicle in the combination is equipped with a roll stability support safety system.
(l) A truck-tractor and semitrailer combination is only eligible for a permit issued under Transportation Code, §623.402(a) if the distance between the front axle of the truck-tractor and the last axle of the semitrailer, measured longitudinally, is approximately 647 inches. For the purposes of this subsection, "approximately 647 inches" means the distance can be up to 15 percent above 647 inches for a total distance of 744.05 inches.
(m) A truck-tractor and semitrailer combination is only eligible for a permit issued under Transportation Code, §623.402(b) if the distance between the front axle of the truck-tractor and the last axle of the semitrailer, measured longitudinally, is approximately 612 inches. For the purposes of this subsection, "approximately 612 inches" means the distance can be up to 15 percent above 612 inches for a total distance of 703.8 inches.
Subchapter D. Permits for Oversize and Overweight Oil Well Related Vehicles
§219.41. General Requirements.
(a) General information.
(1) Permits issued under this subchapter, with the exception of permits issued under §219.45 of this title (relating to Permits for Vehicles Transporting Liquid Products Related to Oil Well Production), are subject to the requirements of this section.
(2) Oil well related vehicles are eligible for:
(A) single-trip mileage permits;
(B) quarterly hubometer permits; and
(C) annual permits.
(b) Permit application. All applications shall be made on a form and in a manner prescribed by the department. An applicant shall provide all applicable information, including:
(1) name, customer identification number, and address of the applicant;
(2) name, telephone number, and email address of contact person;
(3) year, make, and vehicle identification number of the unit;
(4) width, height, and length of the unit;
(5) unit axle and tire information, including number of axles, distance between axles, gauge per axle, axle weights, number of tires, and tire size;
(6) applicant’s USDOT Number if applicant is required by law to have a USDOT Number; and
(7) any other information required by law.
(c) Restrictions.
(1) A vehicle permitted under this subchapter is subject to the restrictions specified in §219.11(l)(2) and (3), and the permittee is responsible for obtaining information concerning current restrictions from the department.
(2) Vehicles permitted under this subchapter may not cross a load restricted bridge when exceeding the posted capacity of such. Vehicles permitted under this subchapter may travel on a load restricted road unless otherwise noted.
(3) A vehicle permitted under this subchapter may travel through highway construction or maintenance areas provided the dimensions do not exceed the construction restrictions as published by the department.
(4) A unit exceeding nine feet in width, 14 feet in height, or 65 feet in length is restricted to daytime movement only.
(d) Transferability. Unless otherwise noted, a permit issued under this subchapter may not be transferred between units or permittees.
(e) Escort requirements. In addition to any other escort requirements specified in this subchapter, vehicles permitted under this subchapter are subject to the escort requirements specified in §219.11(k).
§219.42. Single-Trip Mileage Permits.
(a) General information.
(1) Permits issued under this section are subject to the requirements of §219.41 of this title (relating to General Requirements).
(2) A single-trip mileage permit:
(A) is limited to a maximum of seven consecutive days;
(B) routes the vehicle from the point of origin to the point of destination and has the route listed on the permit; and
(C) allows the unit to be returned to the point of origin on the same permit, provided the return trip is made within the time period stated in the permit.
(3) A unit exceeding 175,000 pounds gross weight must:
(A) have front and rear escort flag vehicles to prevent traffic from traveling beside the unit as it crosses a bridge;
(B) cross all multi-lane bridges by centering the unit on a lane line;
(C) cross all two-lane bridges in the center of the bridge; and
(D) cross each bridge at a speed not greater than 20 miles per hour.
(4) A unit exceeding 12 feet in width must be centered in the outside traffic lane of any highway that has paved shoulders.
(b) Maximum permit weight limits.
(1) The maximum permit weight for any single axle must not exceed 30,000 pounds or 850 pounds per inch of tire width, whichever is less.
(2) The maximum permit weight for any group of axles on a unit will be determined by calculating the "W" weight for the group, using the formulas shown in Figure 2: 43 TAC §219.42(f), titled "Maximum Permit Weight Formulas," and comparing the calculated "W" weight with the corresponding "W" weight that is established in Figure 1: 43 TAC §219.42(f), titled "Maximum Permit Weight Table."
(3) The maximum permit weight per inch of tire width for axles that are steerable must not exceed 950 pounds, and the maximum permit weight per inch of tire width for axles that are not steerable must not exceed 850 pounds.
(4) A unit that does not have any group of axles that exceeds the limits established in Figure 1: 43 TAC §219.42(f), "Maximum Permit Weight Table," and Figure 2: 43 TAC §219.42(f), "Maximum Permit Weight Formulas" will be permitted with a single-trip mileage or quarterly hubometer permit for travel on any route that does not include a load restricted bridge.
(5) A unit that has any group of axles that exceeds the limits established by Figure 1: 43 TAC §219.42(f), "Maximum Permit Weight Table," and Figure 2: 43 TAC §219.42(f), "Maximum Permit Weight Formulas" will be eligible, on an individual case-by-case basis, for a single-trip mileage permit only; permit approval or denial will be based on a detailed route study and an analysis conducted by TxDOT of each bridge on the proposed travel route to determine if the road(s) and bridge(s) are capable of sustaining the movement.
(6) A road or bridge that has been analyzed and determined to be incapable of sustaining the unit will be excluded from the permit route.
(c) Permit application and issuance.
(1) An application for a single-trip mileage permit under this section must be made in accordance with §219.41(b) of this title and shall also include the origin and destination points of the unit.
(2) Upon receipt of the application, the department will review and verify unit size and weight information, check route and mileage to be traveled, compute the permit fee, and advise the applicant of the permit fee.
(3) Upon receipt of the permit fee, the department will advise the applicant of the permit number, and will provide a copy of the permit to the applicant.
(d) Permit fees and refunds.
(1) Minimum fee. The minimum fee for a single-trip mileage permit is either the calculated permit fee or $31, whichever is the greater amount.
(2) Permit fee calculation. The fee for a single-trip mileage permit is calculated by multiplying the number of miles traveled, the highway use factor, and the total rate per mile, and then adding the indirect cost share to the product.
(A) Highway use factor. The highway use factor for a single trip mileage permit is 0.6.
(B) Total rate per mile. The total rate per mile is the combined mileage rates for width, height, and weight for the unit. For a trailer-mounted unit, the total rate per mile is based on the overall width, overall height, and all axle weights, including the truck-tractor axles.
(i) The mileage rate for width is $.06 per mile for each foot (or fraction thereof) above legal width.
(ii) The mileage rate for height is $.04 per mile for each foot (or fraction thereof) above legal height.
(iii) The mileage rate for a single axle or any axle within a group that exceeds 20,000 pounds, but is less than or equal to 25,000 pounds, is calculated by multiplying $.045 times the amount by which the axle or axle group weight exceeds the legal weight for the axle or axle group and dividing the resultant figure by 1,000 pounds.
(iv) The mileage rate for a single axle or any axle within a group that exceeds 25,000 pounds, but is less than or equal to 30,000 pounds, is calculated by multiplying $.055 times the amount by which the axle or axle group weight exceeds the legal weight for the axle or axle group and dividing the resultant figure by 1,000 pounds.
(3) Permit fees for trailer-mounted units.
The permit fee for a trailer-mounted unit is based on the overall width, overall height, and all axle weights, including the truck-tractor axles.
(4) Refunds. Fees for permits issued under this section are non-refundable.
(e) Amendments. A single-trip mileage permit may not be amended unless an exception is granted by the department.
(f) Weight table and formulas. The following table entitled "Maximum Permit Weight Table" is Figure 1: 43 TAC §219.42(f), and the list of formulas entitled, "Maximum Permit Weight Formulas," is Figure 2: 43 TAC §219.42(f).
Figure 1: 43 TAC §219.42(f) — Maximum Permit Weight Table
Official graphic: Texas Secretary of State attached graphic 201502155-1, dated June 8, 2015. Portal: https://texas-sos.appianportalsgov.com/rules-and-meetings?interface=LANDING_PAGE. Length 55 is printed in both the second and third length columns.
| Length (L) feet | Weight (W) lb/ft | Length (L) feet | Weight (W) lb/ft | Length (L) feet | Weight (W) lb/ft |
|---|---|---|---|---|---|
| 4 | 7520 | 30 | 3676 | 55 | 3111 |
| 5 | 6345 | 31 | 3646 | 56 | 3094 |
| 6 | 5947 | 32 | 3616 | 57 | 3077 |
| 7 | 5698 | 33 | 3586 | 58 | 3061 |
| 8 | 5500 | 34 | 3557 | 59 | 3045 |
| 9 | 5326 | 35 | 3529 | 60 | 3030 |
| 10 | 5169 | 36 | 3501 | 61 | 3015 |
| 11 | 5027 | 37 | 3474 | 62 | 3000 |
| 12 | 4898 | 38 | 3448 | 63 | 2985 |
| 13 | 4781 | 39 | 3423 | 64 | 2971 |
| 14 | 4675 | 40 | 3399 | 65 | 2957 |
| 15 | 4579 | 41 | 3376 | 66 | 2943 |
| 16 | 4492 | 42 | 3354 | 67 | 2929 |
| 17 | 4413 | 43 | 3333 | 68 | 2915 |
| 18 | 4340 | 44 | 3313 | 69 | 2901 |
| 19 | 4272 | 45 | 3293 | 70 | 2887 |
| 20 | 4208 | 46 | 3274 | 71 | 2874 |
| 21 | 4146 | 47 | 3255 | 72 | 2861 |
| 22 | 4087 | 48 | 3236 | 73 | 2848 |
| 23 | 4030 | 49 | 3218 | 74 | 2835 |
| 24 | 3974 | 50 | 3200 | 75 | 2822 |
| 25 | 3920 | 51 | 3182 | 76 | 2809 |
| 26 | 3867 | 52 | 3164 | 77 | 2796 |
| 27 | 3815 | 53 | 3146 | 78 | 2783 |
| 28 | 3764 | 54 | 3128 | 79 | 2771 |
| 29 | 3714 | 55 | 3111 | 80 | 2759 |
Figure 2: 43 TAC §219.42(f) — Maximum Permit Weight Formulas
Official graphic: Texas Secretary of State attached graphic 201502155-2, dated June 8, 2015. Portal: https://texas-sos.appianportalsgov.com/rules-and-meetings?interface=LANDING_PAGE
W=T/(L+4 )
"W" - The value of the equivalent distributed load expressed in pounds per linear foot.
"T" - The sum of the axle loads or equivalent axle loads of any group of two or more axles expressed in pounds. Any combination of axle loads may be considered as a group, up to the total number of axles for the unit.
"L" - The length between axles, expressed in feet and measured to the nearest inch, from the center of the first axle to the center of last axle in the axle group, series of groups, or total axles for the unit. A unit with axle groups composed of various numbers of tires per axle or with axle groups with a gauge distance greater than 6.0 feet on each axle may have additional reduction factors applied to each axle before summing “T.” The revised equivalent axle load is calculated by the following formula.
A = (RS)(THE AXLE LOAD)
"A" - Equivalent axle load for axles with gauge greater than 6.0 feet and/or more than four tires.
"R" - A reduction factor for a unit with a gauge distance greater than 6.0 feet, calculated by the following formula.
R = ( 6.0 + G ) / ( 2 G )
"G" - The gauge distance, expressed in feet and measured to the nearest inch, from the center of the outside dual wheels on one side of the axle to the center of the outside dual wheels on the opposite side of the axle. The gauge distance of an axle equipped with two tires per axle must be measured to the nearest inch from center of tire to center of opposite tire.
"S" - A reduction factor based on the number of tires per axle.
S = 1.0 for axles with four or fewer tires, and
S = 0.96 for axles with eight tires.
§219.43. Quarterly Hubometer Permits.
(a) General information.
(1) Permits issued under this section are subject to the requirements of §219.41 of this title (relating to General Requirements).
(2) A quarterly hubometer permit:
(A) is effective for three consecutive months;
(B) allows the unit to travel on all state-maintained highways; and
(C) allows the unit to travel on a state-wide basis.
(3) A unit permitted under this subsection must not exceed any of the following dimensions:
(A) 12 feet in width;
(B) 14 feet, 6 inches in height; and
(C) 95 feet in length.
(4) With the exception of units that are overlength only, a unit operated with a permit issued under this section must be equipped with a hubometer. The permittee must maintain the hubometer in good working condition.
(5) A unit exceeding 175,000 pounds gross weight must:
(A) have front and rear escort flag vehicles to prevent traffic from traveling beside the unit as it crosses a bridge;
(B) cross all multi-lane bridges by centering the unit on a lane line;
(C) cross all two-lane bridges in the center of the bridge; and
(D) cross each bridge at a speed not greater than 20 miles per hour.
(b) Maximum permit weight limits.
(1) The maximum permit weight for any single axle must not exceed 30,000 pounds or 850 pounds per inch of tire width, whichever is less.
(2) The maximum permit weight for any group of axles on a unit will be determined by calculating the "W" weight for the group, using the formulas in Figure 2: 43 TAC §219.42(f), "Maximum Permit Weight Formulas," and comparing the calculated "W" weight with the corresponding "W" weight that is established in Figure 1: 43 TAC §219.42(f), "Maximum Permit Weight Table."
(3) The maximum permit weight per inch of tire width for axles that are steerable must not exceed 950 pounds, and the maximum permit weight per inch of tire width for axles that are not steerable must not exceed 850 pounds.
(4) A unit that does not have any group of axles that exceeds the limits established in Figure 1: 43 TAC §219.42(f), "Maximum Permit Weight Table," and Figure 2: 43 TAC §219.42(f), "Maximum Permit Weight Formulas" will be permitted with a single-trip mileage or quarterly hubometer permit for travel on any route that does not include a load restricted bridge.
(5) A unit that has any group of axles that exceeds the limits established by Figure 1: 43 TAC §219.42(f), "Maximum Permit Weight Table," and Figure 2: 43 TAC §219.42(f), "Maximum Permit Weight Formulas" will be eligible, on an individual case-by-case basis, for a single-trip mileage permit only; permit approval or denial will be based on a detailed route study and an analysis conducted by TxDOT of each bridge on the proposed travel route to determine if the road(s) and bridge(s) are capable of sustaining the movement.
(6) A bridge that has been analyzed and determined to be incapable of sustaining the unit will be excluded from the permit route.
(c) Initial permit application and issuance.
(1) An application for an initial quarterly hubometer permit under this section must be made in accordance with §219.41(b) of this title. In addition, the applicant must provide the current hubometer mileage reading and an initial $31 processing fee.
(2) Upon verification of the unit information and receipt of the permit fee, the department will provide a copy of the permit to the applicant, as well as a renewal application.
(d) Permit renewals and closeouts.
(1) An application for a permit renewal or closeout must be made on a form and in the manner prescribed by the department.
(2) Upon receipt of the renewal application, the department will verify unit information, check mileage traveled on the last permit, calculate the new permit fee, and advise the applicant of the permit fee.
(e) Permit fees.
(1) Minimum fee. The minimum fee for a quarterly hubometer permit is either the calculated permit fee or $31, whichever is the greater amount.
(2) Fees for overlength units. A unit that is overlength only must obtain a quarterly hubometer permit with a fee of $31, but is not required to have a hubometer.
(3) Quarterly hubometer permit fee calculation. The permit fee for a quarterly hubometer permit is calculated by multiplying the hubometer mileage, the highway use factor, and the total rate per mile, and then adding the indirect cost share to the product.
(A) Hubometer mileage. Mileage for a quarterly hubometer permit is determined by the unit's current hubometer mileage reading minus the unit's hubometer mileage reading from the previous quarterly hubometer permit.
(B) Highway use factor. The highway use factor for a quarterly hubometer permit is 0.3.
(C) Total rate per mile. The total rate per mile is the combined mileage rates for width, height, and weight for the unit. The rate per mile for a trailer-mounted unit is based on the overall width, overall height, and all axle weights, including the truck-tractor axles.
(i) The mileage rate for width is $.06 per mile for each foot (or fraction thereof) above legal width.
(ii) The mileage rate for height is $.04 per mile for each foot (or fraction thereof) above legal height.
(iii) The mileage rate for a single axle or any axle within a group that exceeds 20,000 pounds, but is less than or equal to 25,000 pounds, is calculated by multiplying $.045 times the amount by which the axle or axle group weight exceeds the legal weight for the axle or axle group and dividing the resultant figure by 1,000 pounds.
(iv) The mileage rate for a single axle or any axle within a group that exceeds 25,000 pounds, but is less than or equal to 30,000 pounds, is calculated by multiplying $.055 times the amount by which the axle or axle group weight exceeds the legal weight for the axle or axle group and dividing the resultant figure by 1,000 pounds.
(4) Permit fees for trailer-mounted units.
The permit fee for a trailer-mounted unit is based on the overall width, overall height, and all axle weights, including the truck-tractor axles.
(f) Amendments. A quarterly hubometer permit may be amended only to change the following:
(1) if listed on the permit, the hubometer serial number; or
(2) the license plate number.
§219.44. Annual Permits.
(a) General information. Permits issued under this section are subject to the requirements of §219.41 of this title (relating to General Requirements).
(1) Annual self-propelled oil well servicing unit permits.
The fee for an annual self-propelled oil well servicing unit permit is $52 per axle. The indirect cost share is included in this fee.
(2) Annual oil field rig-up truck permits.
(A) An oil field rig-up truck permitted under this section must not exceed:
(i) legal height or length limits, as provided in Transportation Code, Chapter 621, Subchapter C;
(ii) 850 pounds per inch of tire width on the front axle;
(iii) 25,000 pounds on the front axle; or
(iv) legal weight on all other axles.
(B) An oil field rig-up truck, operating under an annual permit, must be registered in accordance with Transportation Code, Chapter 502.
(C) The annual permit fee for an oil field rig-up truck is $52. The indirect cost share is included in this fee.
(D) An annual permit for an oil field rig-up truck allows the unit to travel at nighttime, provided the unit does not exceed nine feet in width.
(3) A permit issued under this section may not be amended.
(4) A permit issued under this section allows travel on a statewide basis and on all state maintained highways.
(b) Permit application and issuance.
(1) An application for an annual permit under this section must be made in accordance with §219.41(b) of this title.
(2) Upon receipt of the application and the appropriate fees, the department will provide a copy of the permit to the applicant.
§219.45. Permits for Vehicles Transporting Liquid Products Related to Oil Well Production.
(a) General provisions. This section applies to the following vehicles which may secure an annual permit issued under provisions of Transportation Code, Chapter 623, Subchapter G, to haul liquid loads over all state-maintained highways.
(1) A vehicle combination consisting of a truck-tractor and semi-trailer specifically designed with a tank and pump unit for transporting:
(A) liquid fracking products, liquid oil well waste products, or unrefined liquid petroleum products to an oil well; or
(B) unrefined liquid petroleum products or liquid oil well waste products from an oil well not connected to a pipeline.
(2) A permit issued under this section is effective for one year beginning on the effective date.
(b) Application for permit.
(1) An application for an annual permit under this section must be made in accordance with §219.41(b) of this title (relating to General Requirements).
(2) The permit request must be received by the department not more than 14 days prior to the date that the permit is to begin.
(c) Permit qualifications and requirements.
(1) The semi-trailer must be of legal size and weight.
(2) Only one semi-trailer will be listed on a permit.
(3) The permit may be transferred from an existing trailer being removed from service and placed on a new trailer being added to the permittee's fleet, if the permittee supplies the department with:
(A) the existing valid permit number;
(B) the make and model of the new trailer;
(C) the license plate number of the new trailer; and
(D) a transfer fee of $31 per permit to cover administrative costs.
(d) Fees.
(1) The permit fee is based on the axles of the semi-trailer and the drive axles of the truck-tractor. The fee for the permit, which includes the indirect cost share, is determined as follows:
(A) $52 per axle--to haul liquid oil well waste products or unrefined liquid petroleum products from oil wells not connected by a pipeline and return empty;
(B) $52 per axle--to haul liquid products related to oil well production to an oil well and return empty; and
(C) $104 per axle--to haul liquid products related to oil well production to an oil well and return with liquid oil well waste products or unrefined liquid petroleum products from an oil well not connected to a pipeline.
(2) Each permittee will be charged a $20 issuance fee in addition to the permit fee.
(e) Permit movement conditions. The permit load must not cross any load-restricted bridge when exceeding the posted capacity of such. SUBCHAPTER E. PERMITS FOR OVERSIZE AND OVERWEIGHT UNLADEN LIFT EQUIPMENT MOTOR
VEHICLES
Subchapter E. Permits for Oversize and Overweight Unladen Lift Equipment Motor Vehicles
§219.60. Purpose.
The sections in this subchapter set forth the requirements and procedures applicable to permits issued for unladen lift equipment motor vehicles under the provisions of Transportation Code, Chapter 623, Subchapters I and J.
§219.61. General Requirements for Permits for Oversize and Overweight Unladen Lift Equipment Motor Vehicles.
(a) General information.
(1) Unless otherwise noted, permits issued under this subchapter are subject to the requirements of this section.
(2) Unladen lift equipment motor vehicles are eligible for an annual permit under this subchapter.
(3) Unladen lift equipment motor vehicles are also eligible for the following permits under this subchapter at weights above those established by §219.11(d)(2) of this title (relating to General Oversize/Overweight Permit Requirements and Procedures):
(A) single-trip mileage permits; and
(B) quarterly hubometer permits.
(b) Permit application. An application shall be made on a form and in a manner prescribed by the department. The applicant shall provide all applicable information, including:
(1) name, customer identification number, and address of the applicant;
(2) name, telephone number, and email address of contact person;
(3) year, make and vehicle identification number of the unladen lift equipment motor vehicle;
(4) width, height, and length of the unladen lift equipment motor vehicle;
(5) unladen lift equipment motor vehicle axle and tire information, including the number of axles, distance between axles, gauge per axle, axle weights, number of tires, and tire size;
(6) applicant’s USDOT Number if applicant is required by law to have a USDOT Number; and
(7) any other information required by law.
(c) Restrictions.
(1) An unladen lift equipment motor vehicle permitted under this subchapter is subject to the restrictions specified in §219.11(l)(2) and (3) of this title, and the permittee is responsible for obtaining information concerning current restrictions from the department.
(2) An unladen lift equipment motor vehicle permitted under this subchapter may travel through highway construction or maintenance areas provided the dimensions do not exceed the construction restrictions as published by the department.
(3) An unladen lift equipment motor vehicle permitted under this subchapter may only be operated during daytime, unless:
(A) the unladen lift equipment motor vehicle is overweight only; or
(B) the unladen lift equipment motor vehicle complies with one of the following, regardless of whether the unladen lift equipment motor vehicle is overweight:
(i) the unladen lift equipment motor vehicle does not exceed nine feet in width, 14 feet in height, or 65 feet in length; or
(ii) the unladen lift equipment motor vehicle is accompanied by a front and rear escort flag vehicle and does not exceed:
(I) 10 feet, 6 inches in width;
(II) 14 feet in height; or
(III) 95 feet in length.
(d) Transferability. Unless otherwise noted, a permit issued under this subchapter may not be transferred between unladen lift equipment motor vehicles or between permittees.
(e) Escort requirements. In addition to any other escort requirements specified in this subchapter, unladen lift equipment motor vehicles permitted under this subchapter are subject to the escort requirements specified in §219.11(k) of this title.
§219.62. Single-Trip Mileage Permits.
(a) General information.
(1) Permits issued under this section are subject to the requirements of §219.61 of this title (relating to General Requirements for Permits for Oversize and Overweight Unladen Lift Equipment Motor Vehicles).
(2) A single-trip mileage permit:
(A) is limited to a maximum of seven consecutive days;
(B) is routed from the point of origin to the point of destination and has the route listed on the permit; and
(C) allows the unladen lift equipment motor vehicle to be returned to the point of origin on the same permit, provided the return trip is made within the time period stated in the permit.
(3) An unladen lift equipment motor vehicle exceeding 175,000 pounds gross weight must:
(A) have front and rear escort flag vehicles to prevent traffic from traveling beside the unladen lift equipment motor vehicle as it crosses a bridge;
(B) cross all multi-lane bridges by centering the unladen lift equipment motor vehicle on a lane line;
(C) cross all two-lane bridges in the center of the bridge; and
(D) cross each bridge at a speed not greater than 20 miles per hour.
(4) An unladen lift equipment motor vehicle exceeding 12 feet in width must be centered in the outside traffic lane of any highway that has paved shoulders.
(5) Except as otherwise provided in this section, the permitted unladen lift equipment motor vehicle must not cross a load-restricted bridge when exceeding the posted capacity of the bridge.
(b) Maximum permit weight limits.
(1) The maximum permit weight for any single axle must not exceed 30,000 pounds or 850 pounds per inch of tire width, whichever is less.
(2) The maximum permit weight for any group of axles on an unladen lift equipment motor vehicle is determined by calculating the "W" weight for the group, using the formulas shown in Figure 2: 43 TAC §219.62(f), "Maximum Permit Weight Formulas," and comparing the calculated "W" weight with the corresponding "W" weight that is established in Figure 1: 43 TAC §219.62(f), "Maximum Permit Weight Table."
(3) The maximum permit weight per inch of tire width for axles that are steerable must not exceed 950 pounds, and the maximum permit weight per inch of tire width for axles that are not steerable must not exceed 850 pounds.
(4) An applicant with an unladen lift equipment motor vehicle that has any group of axles that exceeds the limits established by Figure 1: 43 TAC §219.62(f),"Maximum Permit Weight Table," and Figure 2: 43 TAC §219.62(f), "Maximum Permit Weight Formulas," must comply with the following process and requirements:
(A) submit the following to the department to determine if a permit can be issued:
(i) a detailed diagram, on a form prescribed by the department, which illustrates the required information listed in §219.61(b)(5) of this title;
(ii) the exact beginning and ending points relative to a state highway; and
(iii) the name and contact information of the applicant's TxDOT-approved licensed professional engineer.
(B) The department will select and provide the applicant with a tentative route based on the size of the unladen lift equipment motor vehicle, excluding the weight. The applicant must inspect the tentative route and advise the department, in writing, that the route is capable of accommodating the unladen lift equipment motor vehicle.
(C) Before the department will issue a permit, the applicant's TxDOT-approved licensed professional engineer must submit to TxDOT a written certification that includes a detailed structural analysis of the bridges on the proposed route demonstrating that the bridges and culverts on the travel route are capable of sustaining the unladen lift equipment motor vehicle. The certification must be approved by TxDOT and submitted to the department before the department will issue the permit.
(c) Permit application and issuance.
(1) An application for a single-trip mileage permit under this section must be made in accordance with §219.61(b) of this title and must also include the origin and destination points of the unladen lift equipment motor vehicle.
(2) Upon receipt of the application, the department will review and verify size and weight information, check the route and mileage to be traveled, compute the permit fee, and advise the applicant of the permit fee.
(3) Upon receipt of the permit fee, the department will advise the applicant of the permit number and will provide a copy of the permit to the applicant.
(d) Permit fees and refunds.
(1) Minimum fee. The minimum fee for a single-trip mileage permit is either the calculated permit fee or $31, whichever is the greater amount.
(2) Permit fee calculation. The permit fee for a single-trip mileage permit is calculated by multiplying the number of miles traveled, the highway use factor, and the total rate per mile, and then adding the indirect cost share to the product.
(A) Highway use factor. The highway use factor for a single-trip mileage permit is 0.6.
(B) Total rate per mile. The total rate per mile is the combined mileage rates for width, height, and weight for the unladen lift equipment motor vehicle.
(i) The mileage rate for width is $.06 per mile for each foot (or fraction thereof) above legal width.
(ii) The mileage rate for height is $.04 per mile for each foot (or fraction thereof) above legal height.
(iii) The mileage rate for a single axle or any axle within a group that exceeds 20,000 pounds, but is less than or equal to 25,000 pounds, is calculated by multiplying $.045 times the amount by which the axle or axle group weight exceeds the legal weight for the axle or axle group and dividing the resultant figure by 1,000 pounds.
(iv) The mileage rate for a single axle or any axle within a group that exceeds 25,000 pounds, but is less than or equal to 30,000 pounds, is calculated by multiplying $.055 times the amount by which the axle or axle group weight exceeds the legal weight for the axle or axle group and dividing the resultant figure by 1,000 pounds.
(3) Refunds. Fees for permits issued under this section are non-refundable.
(e) Amendments. A single-trip mileage permit issued under this section may not be amended unless an exception is granted by the department.
(f) Weight table and formulas. The following table entitled "Maximum Permit Weight Table" is Figure 1: 43 TAC §219.62(f), and the list of formulas entitled "Maximum Permit Weight Formulas," is Figure 2: 43 TAC §219.62(f).
Figure 1: 43 TAC §219.62(f) — Maximum Permit Weight Table
Official graphic: Texas Secretary of State attached graphic 201502158-1, dated June 8, 2015. Portal: https://texas-sos.appianportalsgov.com/rules-and-meetings?interface=LANDING_PAGE. Length 55 is printed in both the second and third length columns. The values match Figure 1 of §219.42(f).
| Length (L) feet | Weight (W) lb/ft | Length (L) feet | Weight (W) lb/ft | Length (L) feet | Weight (W) lb/ft |
|---|---|---|---|---|---|
| 4 | 7520 | 30 | 3676 | 55 | 3111 |
| 5 | 6345 | 31 | 3646 | 56 | 3094 |
| 6 | 5947 | 32 | 3616 | 57 | 3077 |
| 7 | 5698 | 33 | 3586 | 58 | 3061 |
| 8 | 5500 | 34 | 3557 | 59 | 3045 |
| 9 | 5326 | 35 | 3529 | 60 | 3030 |
| 10 | 5169 | 36 | 3501 | 61 | 3015 |
| 11 | 5027 | 37 | 3474 | 62 | 3000 |
| 12 | 4898 | 38 | 3448 | 63 | 2985 |
| 13 | 4781 | 39 | 3423 | 64 | 2971 |
| 14 | 4675 | 40 | 3399 | 65 | 2957 |
| 15 | 4579 | 41 | 3376 | 66 | 2943 |
| 16 | 4492 | 42 | 3354 | 67 | 2929 |
| 17 | 4413 | 43 | 3333 | 68 | 2915 |
| 18 | 4340 | 44 | 3313 | 69 | 2901 |
| 19 | 4272 | 45 | 3293 | 70 | 2887 |
| 20 | 4208 | 46 | 3274 | 71 | 2874 |
| 21 | 4146 | 47 | 3255 | 72 | 2861 |
| 22 | 4087 | 48 | 3236 | 73 | 2848 |
| 23 | 4030 | 49 | 3218 | 74 | 2835 |
| 24 | 3974 | 50 | 3200 | 75 | 2822 |
| 25 | 3920 | 51 | 3182 | 76 | 2809 |
| 26 | 3867 | 52 | 3164 | 77 | 2796 |
| 27 | 3815 | 53 | 3146 | 78 | 2783 |
| 28 | 3764 | 54 | 3128 | 79 | 2771 |
| 29 | 3714 | 55 | 3111 | 80 | 2759 |
Figure 2: 43 TAC §219.62(f) — Maximum Permit Weight Formulas
Official graphic: Texas Secretary of State attached graphic 201502158-2, dated June 8, 2015. Portal: https://texas-sos.appianportalsgov.com/rules-and-meetings?interface=LANDING_PAGE
W=T/(L+4)
“W” - The value of the equivalent distributed load expressed in pounds per linear foot.
“T” - The sum of the axle loads or equivalent axle loads of any group of two or more axles expressed in pounds. Any combination of axle loads may be considered as a group, up to the total number of axles for the unit.
“L” - The length between axles, expressed in feet and measured to the nearest inch, from the center of the first axle to the center of last axle in the axle group, series of groups, or total axles for the unit. A unit with axle groups composed of various numbers of tires per axle or with axle groups with a gauge distance greater than 6.0 feet on each axle may have additional reduction factors applied to each axle before summing “T.” The revised equivalent axle load is calculated by the following formula.
A = (RS)(THE AXLE LOAD)
“A” - Equivalent axle load for axles with gauge greater than 6.0 feet and/or more than four tires.
“R” - A reduction factor for a unit with a gauge distance greater than 6.0 feet, calculated by the following formula.
R = ( 6.0 + G ) / ( 2 G )
“G” - The gauge distance, expressed in feet and measured to the nearest inch, from the center of the outside dual wheels on one side of the axle to the center of the outside dual wheels on the opposite side of the axle. The gauge distance of an axle equipped with two tires per axle must be measured to the nearest inch from center of tire to center of opposite tire.
“S” - A reduction factor based on the number of tires per axle.
S = 1.0 for axles with four or fewer tires, and
S = 0.96 for axles with eight tires.
§219.63. Quarterly Hubometer Permits.
(a) General information.
(1) Permits issued under this section are subject to the requirements of §219.61 of this title (relating to General Requirements for Permits for Oversize and Overweight Unladen Lift Equipment Motor Vehicles).
(2) A quarterly hubometer permit:
(A) is effective for three consecutive months;
(B) allows the unladen lift equipment motor vehicle to travel on all state-maintained highways; and
(C) allows the unladen lift equipment motor vehicle to travel on a state-wide basis.
(3) An unladen lift equipment motor vehicle permitted under this section must not exceed any of the following dimensions:
(A) 12 feet in width;
(B) 14 feet, 6 inches in height; or
(C) 95 feet in length.
(4) With the exception of unladen lift equipment motor vehicles that are overlength only, unladen lift equipment motor vehicles operated with a quarterly hubometer permit must be equipped with a hubometer. The permittee must maintain the hubometer in good working condition.
(5) An unladen lift equipment motor vehicle exceeding 175,000 pounds gross weight must:
(A) have front and rear escort flag vehicles to prevent traffic from traveling beside the unladen lift equipment motor vehicle as it crosses a bridge;
(B) cross all multi-lane bridges by centering the unladen lift equipment motor vehicle on a lane line;
(C) cross all two-lane bridges in the center of the bridge; and
(D) cross each bridge at a speed not greater than 20 miles per hour.
(6) The permitted unladen lift equipment motor vehicle must not cross a load-restricted bridge when exceeding the posted capacity of the bridge.
(7) The permit may be amended only to change the following:
(A) if listed on the permit, the hubometer serial number; or
(B) the license plate number.
(b) Maximum permit weight limits.
(1) The maximum permit weight for any single axle must not exceed 30,000 pounds or 850 pounds per inch of tire width, whichever is less.
(2) The maximum permit weight for any group of axles on an unladen lift equipment motor vehicle will be determined by calculating the "W" weight for the group, using the formulas in Figure 2: 43 TAC §219.62(f), "Maximum Permit Weight Formulas," and comparing the calculated "W" weight with the corresponding "W" weight that is established in Figure 1: 43 TAC §219.62(f), "Maximum Permit Weight Table."
(3) The maximum permit weight per inch of tire width for axles that are steerable must not exceed 950 pounds, and the maximum permit weight per inch of tire width for axles that are not steerable must not exceed 850 pounds.
(4) An unladen lift equipment motor vehicle that has any group of axles that exceeds the limits established by Figure 1: 43 TAC §219.62(f), "Maximum Permit Weight Table," and Figure 2: 43 TAC §219.62(f), "Maximum Permit Weight Formulas," is not eligible for a permit under this section; however, it is eligible for a permit under §219.62 of this title (relating to Single-Trip Mileage Permits).
(c) Initial permit application and issuance.
(1) An application for an initial quarterly hubometer permit must be made in accordance with §219.61(b) of this title. In addition, the applicant must provide the current hubometer mileage reading and an initial $31 processing fee.
(2) Upon verification of the unladen lift equipment motor vehicle information and receipt of the permit fee, the department will provide a copy of the permit to the applicant, and will also provide a renewal application form to the applicant.
(d) Permit renewals and closeouts.
(1) An application for a permit renewal or closeout must be made on a form and in a manner prescribed by the department.
(2) Upon receipt of the renewal application, the department will verify the unladen lift equipment motor vehicle information, check mileage traveled on the last permit, calculate the new permit fee, and advise the applicant of the permit fee.
(e) Permit fees.
(1) Minimum fee. The minimum fee for a quarterly hubometer permit is either the calculated permit fee or $31, whichever is the greater amount.
(2) Fees for overlength unladen lift equipment motor vehicles. An unladen lift equipment motor vehicle that is overlength only is not required to have a hubometer. The fee for this permit is $31.
(3) Quarterly hubometer permit fee calculation. The permit fee for a quarterly hubometer permit is calculated by multiplying the hubometer mileage, the highway use factor, and the total rate per mile, and then adding the indirect cost share to the product.
(A) Hubometer mileage. Mileage for a quarterly hubometer permit is determined by the unladen lift equipment motor vehicle’s current hubometer mileage reading minus the unladen lift equipment motor vehicle’s hubometer mileage reading from the previous quarterly hubometer permit.
(B) Highway use factor. The highway use factor for a quarterly hubometer permit is 0.3.
(C) Total rate per mile. The total rate per mile is the combined mileage rates for width, height, and weight for the unladen lift equipment motor vehicle.
(i) The mileage rate for width is $.06 per mile for each foot (or fraction thereof) above legal width.
(ii) The mileage rate for height is $.04 per mile for each foot (or fraction thereof) above legal height.
(iii) The mileage rate for a single axle or any axle within a group that exceeds 20,000 pounds, but is less than or equal to 25,000 pounds, is calculated by multiplying $.045 times the amount by which the axle or axle group weight exceeds the legal weight for the axle or axle group and dividing the resultant figure by 1,000 pounds.
(iv) The mileage rate for a single axle or any axle within a group that exceeds 25,000 pounds, but is less than or equal to 30,000 pounds, is calculated by multiplying $.055 times the amount by which the axle or axle group weight exceeds the legal weight for the axle or axle group and dividing the resultant figure by 1,000 pounds.
§219.64. Annual Permits.
(a) General information. Permits issued under this section are subject to the requirements of §219.61 of this title (relating to General Requirements for Permits for Oversize and Overweight Unladen Lift Equipment Motor Vehicles).
(1) An unladen lift equipment motor vehicle permitted under this section must not exceed:
(A) the weight limits established in §219.11(d)(1), (2), and (3) of this title (relating to General Oversize/Overweight Permit Requirements and Procedures);
(B) a gross weight of 120,000 pounds;
(C) legal length and height limits as specified in Transportation Code, Chapter 621, Subchapter C; and
(D) 10 feet in width.
(2) A permit issued under this section may not be amended.
(3) An unladen lift equipment motor vehicle permitted under this section must not cross a load-restricted bridge or a load-restricted road when exceeding the posted capacity of such.
(b) Permit application and issuance.
(1) Initial permit application. An application for an annual permit under this section must be made in accordance with §219.61(b) of this title.
(2) Permit issuance. Upon receipt of the application and the appropriate permit fee, the department will verify the application information and provide the permit to the applicant.
Subchapter F. Compliance
§219.81. Applicability.
(a) A person operating or loading a vehicle for which a permit under this chapter is required shall comply with all applicable terms, conditions, and requirements of the permit, and with this chapter and Transportation Code, Chapters 621, 622, or 623 as applicable.
(b) A person loading a vehicle or operating on a public road or highway a vehicle for which a permit under this chapter is not required shall comply with the weight and size provisions of Transportation Code, Chapters 621, 622, or 623.
Subchapter G. Records and Inspections
§219.102. Records.
(a) General records to be maintained. Each person who is subject to this chapter shall maintain the following records if information in such a record is necessary to verify the person's operation:
(1) operational logs, insurance certificates, and documents to verify the person's operations;
(2) complete and accurate records of services performed; and
(3) all certificate of title documents, shipper's certificate of weight, including information used to support the shipper's certificate of weight, weight tickets, permits for oversize or overweight vehicles and loads, dispatch records, load tickets, waybill or any other document that verify the operations of the vehicle to determine the actual weight, insurance coverage, size or capacity of the vehicle, and the size or weight of the commodity being transported.
(b) Evidence of permits.
(1) Except as stated otherwise in §219.13(e)(4)(B)(ii) of this title (relating to Time Permits), the original permit, a print copy of the permit, or an electronic copy of the permit must be kept in the permitted vehicle until the permit terminates or expires.
(2) Except as stated otherwise in §219.13(e)(4)(B)(ii), an operator of a vehicle operating under a permit issued under Transportation Code, Subtitle E, shall, on request, provide the original permit, a print copy of the permit, or an electronic copy of the permit to a department inspector or to a peace officer, as defined by Code of Criminal Procedure, Article 2.12.
(A) If the department provides a permit electronically, the vehicle operator may provide a legible and accurate image of the permit displayed on a wireless communication device.
(B) The authorization of the use of a wireless communication device to display permit information under this paragraph does not prevent the State Office of Administrative Hearings or a court of competent jurisdiction from requiring a person to provide a paper copy of the person's evidence of permit in a hearing or trial or in connection with discovery proceedings.
(c) Preservation and destruction of records. Records required under this section shall be maintained for not less than two years, except that drivers' time cards and logs shall be maintained for not less than six months.
not copied yet
Section 219.3 is named in the adoption preamble and is not reprinted as rule text in the June 27, 2024 exhibit, so it is not on this page. The exhibit marks §§219.84, 219.86, and 219.123 as repealed; those bracketed repeal texts are not copied.
Source
- Official URL: https://ftp.txdmv.gov/pub/txdmv-info/ogc/rules/2024/Web-Chap-219-Adopt.pdf
- Accessed: 2026-11-13
- Editorial copy for Heavy Haul Reg Ref; controlling text is the issuing authority’s publication.